Bedford Screen Kit (2 PACK) 60 min Approximate assembly time for 2 panels Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18003 (CEDAR COLOR) EC18004 (GRAY COLOR) VER.
EC18003 / EC18004 GENERAL INFORMATION ASSEMBLY INSTRUCTIONS IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18003 / EC18004 STEP 1: LAY OUT MATERIALS A B Horizontal Board (10) 3/8" x 2 3/4" x 34 1/4" Horizontal Picket (24) 1/4" x 1 1/4" x 34 1/4" C D E F Post (4) 5/8" x 5/8" x 42 5/8" Middle Post (2) 5/8" x 5/8" x 39" Post Anchor - Left (2) 3/4" x 3/4" x 18 1/4" Post Anchor - Right (2) 3/4" x 3/4" x 18 1/4" G H I J Top Rail (2) 7/8" x 7/8" x 35 3/4" Bottom Rail (2) 7/8" x 7/8" x 35 3/4" 3/4" Steel Screw (20) Joiner Clip (4) www.encloscreens.
EC18003 / EC18004 ASSEMBLY INSTRUCTIONS STEP 2: INSERTING THE PICKETS AND BOARDS STEP 2.1 b Identify (1) Top Rail (G) and (1) Bottom Rail (H) as shown below. Set the rails aside for now. G Preview H Bottom rail identified by pre-drilled hole Preview STEP 2.2 1. Take (1) Post (C) and arrange it so the routed holes face towards (1) Middle Post (D). 2. Insert a total of (12) Horizontal Pickets (B) and (5) Horizontal Boards (A) into the holes in the post and the middle post.
ASSEMBLY INSTRUCTIONS EC18003 / EC18004 STEP 3: INSTALLING THE RAILS Preview STEP 3.1 1 1. Take a post and insert the routed holes over the boards and pickets. 2. Slide (1) Top Rail (G) over the posts until the pre-drilled holes align. 3. Drive (2) 3/4" screws (I) into the pre-drilled holes. G 2 Align 3 I www.encloscreens.
EC18003 / EC18004 ASSEMBLY INSTRUCTIONS Preview STEP 3.2 1. Slide (1) Bottom Rail (H) up over the posts until the predrilled holes align with the top holes of the post bottom as shown below. 2. Keeping the holes aligned, take (1) Post Anchor - Right (F) and (1) Post Anchor - Left (E) and slide them until the predrilled holes align with the lowest holes on the posts. 3. Drive (4) 3/4" screws into the aligned pre-drilled holes. 1 2 H E F 3 Align 6 Align www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18003 / EC18004 STEP 4: ASSEMBLING THE SECOND PANEL STEP 4.1 b Repeat Steps 2-4 to assemble the second panel. STEP 5: INSTALLING PANELS IN THE GROUND Preview STEP 5.1 1. Move the screen to its final location and mark where the posts meet the ground. 2. Attempt to push the screen into the ground. 1 2 Push down on posts with both hands. www.encloscreens.
EC18003 / EC18004 ASSEMBLY INSTRUCTIONS STEP 5.2 b STEPS 5.2 and 5.3 are only needed if your ground is too hard for STEP 5.1. 1. Loosen the top 6" of the ground with a claw hammer. 2. Add water to loosened soil. 3. Use a block of wood to protect the post and gently hammer each post into the ground. 3 2 1 STEP 5.3 1. If your ground is very hard, dig a hole 8" in diameter and 10" deep, large enough to accommodate one post from each panel. 2. Level the screen, backfill excavated dirt, and tamp as needed.
ASSEMBLY INSTRUCTIONS EC18003 / EC18004 STEP 6: CONNECTING THE PANELS STEP 6.1 1. Straight Line Application: Install the Joiner Clips (J) as shown below. 2. Corner Application: Install the Joiner Clips (J) as shown below. J 1 I 2 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18003 (CEDAR COLOR) EC18004 (GRAY COLOR) VER.
