Lincoln Screen Kit 90 min Approximate assembly time for 2 screens Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18001 (CEDAR COLOR) EC18002 (GRAY COLOR) VER.
EC18001 / EC18002 GENERAL INFORMATION ASSEMBLY INSTRUCTIONS IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 1: LAY OUT MATERIALS A B Post Cap (4) Joiner Clip (4) C D Top view F Top view Post Board (28) 3/8" x 3" x 41 1/2" G Left Post (2) 1 1/8" x 1 1/8" x 42 3/4" Right Post (2) 1 1/8" x 1 1/8" x 42 3/4" E Post Anchor (4) 1" x 1" x 24" www.encloscreens.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 2: INSERT PRIVACY BOARD STEP 2.1 STEP 2.2 b Orient Left Post (C) and Right Post (D) as shown below. 1. Insert a Privacy Board (F) into the grooves of the left and right post. 2. Slide the privacy board until the bottom of the board is 2 3/4" above the bottom of the post. Preview Top of Post 2 ½ in 1 F Align C 2 D 4 ½ in 4 2 ¾ in www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 3: ASSEMBLE THE FIRST SCREEN STEP 3.1 b Insert 13 additional privacy boards into the post channels. Preview Preview STEP 3.2 1. Flip the screen so that the bottom of the posts are facing up. Insert (2) Post Anchors (E), into the posts until the pre-drilled hole in the anchors and posts align as shown below. 2. Drive (4) 1" Stainless Steel Screws (G) into the pre-drilled holes in the posts to secure the privacy boards and post anchors.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 4: ASSEMBLE THE SECOND SCREEN STEP 4.1 b Repeat Steps 2-3 in order to assemble the second screen. STEP 5: INSTALLING THE SCREEN IN THE GROUND STEP 5.1 1. Move the screen to its final location and identify where the posts are located. Attempt to push the unit into the ground as illustrated. 2. If your ground is too hard, loosen the top 6" or 7" of the ground with a claw hammer as illustrated. 3. Add water to loosened soil. 4.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 5.2 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. ($15-$20 on Amazon.com). 2. with water as illustrated. 3. Push the panel posts into the holes. 1 2 www.encloscreens.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 5.3 b If your ground is really hard, you may need to dig a hole 8" in diameter and 14" deep to accommodate one post from each panel into the same hole. 8" 14" STEP 5.4 b Level the screen as necessary, backfill excavated dirt, and tamp if needed. 8 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 6: CONNECT THE SCREENS STEP 6.1 1. Straight Line Application: Connect the screens as shown below using Joiner Clips (B) and 1" Stainless Steel Screws. 2. Corner Application: Connect the screens as shown below using Joiner Clips (B) and 1" Stainless Steel Screws. B 1 B B 2 B www.encloscreens.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 7: INSTALL POST CAPS STEP 7.1 b Install Post Caps (A) into the top of the posts. A 10 www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18001 (CEDAR COLOR) EC18002 (GRAY COLOR) VER.
