Lincoln Screen Kit 90 min Approximate assembly time for 2 screens Scan the QR code for an assembly video ASSEMBLY INSTRUCTIONS www.encloscreens.com EC18001 (CEDAR COLOR) EC18002 (CHARCOAL COLOR) VER.
EC18001 / EC18002 GENERAL INFORMATION ASSEMBLY INSTRUCTIONS IMPORTANT j Check the inside of the larger pieces in your box for other materials packed inside. j When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. j We recommend an area approximately 5’x 8’ for unobstructed assembling. j You should not need to use excessive force when assembling components.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 Detailed Product Dimensions & Specifications 41 3/4 in 42 3/4 in 42 in 16 in 2 3/4 in 40 3/4 in www.encloscreens.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B F Post Cap (4) Joiner Clip (2) C D Post Board (28) 3/8" x 3" x 41 1/2" Top view Top view G 1” Stainless Steel Screw (16) Left Post (2) 1 1/8" x 1 1/8" x 42 3/4" Right Post (2) 1 1/8" x 1 1/8" x 42 3/4" H E Post Anchor (4) 1" x 1" x 24" 4 Spacer (2) 5/8" x 5/8" x 2 3/4" www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 2: INSERT PRIVACY BOARD STEP 2.1 STEP 2.2 b Position (2) Left Posts (C) and Right Posts (D) so the pre-drilled holes for both posts face forward and the open channels face towards each other as shown. 1. Insert a Privacy Board (F) into the grooves of the left and right post. 2. Insert (1) Spacer (H) into the bottom of each post until it is flush with the post bottom. Slide the board until it rests on the spacers.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 3: ASSEMBLE THE FIRST SCREEN STEP 3.1 b Insert 13 additional privacy boards into the post channels. Preview Preview STEP 3.2 1. Flip the screen so that the bottom of the posts are facing up. Remove the (2) spacers, then insert (2) Post Anchors (E), into the posts until the pre-drilled hole in the anchors and posts align as shown below. 2.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 4: ASSEMBLE THE SECOND SCREEN STEP 4.1 b Repeat Steps 2-3 in order to assemble the second screen. STEP 5: INSTALLING THE SCREEN IN THE GROUND STEP 5.1 1. Move the screen to its final location and identify where the posts are located. Attempt to push the unit into the ground as illustrated. 2. If your ground is too hard, loosen the top 6" or 7" of the ground with a claw hammer as illustrated. 3. Add water to loosened soil. 4.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 5.2 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. 3. Push the panel posts into the holes. 1 2 8 3 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 5.3 b If your ground is really hard, you may need to dig a hole 8" in diameter and 14" deep to accommodate one post from each panel into the same hole. 8" 14" STEP 5.4 b Level the screen as necessary, backfill excavated dirt, and tamp if needed. www.encloscreens.
EC18001 / EC18002 ASSEMBLY INSTRUCTIONS STEP 6: CONNECT THE SCREENS STEP 6.1 1. Straight Line Application: Connect the screens as shown below using Joiner Clips (B) and 1" Stainless Steel Screws. 2. Corner Application: Connect the screens as shown below using Joiner Clips (B) and 1" Stainless Steel Screws. B 1 B B 2 B 10 www.encloscreens.
ASSEMBLY INSTRUCTIONS EC18001 / EC18002 STEP 7: INSTALL POST CAPS STEP 7.1 b Install Post Caps (A) into the top of the posts. NOTE: If the fit is tight, use a hammer and a piece of cardboard to protect the post cap to tap the cap into place. A www.encloscreens.
www.encloscreens.com support@encloscreens.com 704-892-5222 877-234-6196 6935 Reames Rd. Ste. K. Charlotte, NC 28216 ASSEMBLY INSTRUCTIONS EC18001 (CEDAR COLOR) EC18002 (CHARCOAL COLOR) VER.
