Customer Support support@enacfireglobal.com (US/CA) moongu@enacfireglobal.
Product Overview 1. Charging Case LED Light 2. Charging Port 3. Multifunctional Button 4. Earphone LED 5. Magnetic Charging Pin 6.
Power On & Pairing Approach 1 - With Charging Case 1. Take out earphones from the charging case 2. Select ‘ENACFIRE E90’ from Bluetooth list sess 0AM
Approach 2 - Without Charging Case Touch ouch 22 ne 0, earphones for 2 seconds. Release when you hear the prompt sound 'Power on' with Blue light on. sec = 1. Power On: Touch the 5 5 2. Pairing: Earphones will pair automatically with Right earphone Blue and White light flash alternately . 3.
Incoming call Answer call/End call Tap the Left/ Right earphone once L/R Reject call Touch the Left/ Right earphone for 2 seconds “4 Touch for 2 sec i.
Music Pause/ Play Tap the Left/ Right earphone once to pause / play music in the music mode (Some phones may require to start a media player first) Voice Assistant Tap the Left / Right earphone 3 times, your device’s Voice Assistant will be activated with the 'Beep' prompt sound
Next Song Or Double-tap the Right earphone b. Previous Song S| a) Double-tap the Left earphone >> © Adjust Volume Touch and hold the Left earphone to decrease volume Touch and hold the Right earphone to increase volume rd 4) © 4) + ) Note: Above functions are not supported when the earphone is used in single. Prompt sound ‘Beep’ will be produced when the volume reach minimum or maximum level.
Power Off Mode1 With Charging Case Put the earphones back to the charging case, they will power off automatically. Note: Only put the Left earphone into the charging case, the Right earphone will stay connected. Only put the Right earphone into the charging case, the Left earphone will be disconnected and start pairing. Mode 2 Without Charging Case 1. Turn off Bluetooth to disconnect the earphones 2.
Single Mode single With Charging Case Earphone 1. Take out Left / Right earphone from the charging case 2. Select 'ENACFIRE E90' from Bluetooth list 1. Make sure both earphones are turn off 2. Touch the Left / Right earphone for 4 seconds. Release Without Charging Case when you hear prompt sound ‘Pairing’ with Blue and White light flash alternately. 3.
Charging Earphones Charging Status Open and close the charging case cap, wait for 3 seconds The leftmost LED light on: Left earphone is charging The rightmost LED light on: Right earphone is charging When the earphone is fully charged, LED light will turn off Note: It takes about 1.5 hours to fully charge the earphones Charging Case Charging Status Open and close the charging case cap Lights on charging case stand for the remaining battery capacity Note: It takes about 1.
Note Please follow below steps when both earphones fail to pair with each other or occur connection related issues 1. Turn off Bluetooth to disconnect the earphones 2. Touch either one earphone for 8 seconds to power off both earphones 3. Touch and hold the power button of Left earphone for 8 seconds with White lights flash 3 times 4, Touch and hold the power button of Right earphone for 8 seconds with White lights flash 3 times 5. Put the earphones back to the charging case 6.
Safety Instruction Using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety. Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds. Do not use earphones in thunderstorm weather, the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning.
Q&A Q: Why the music cuts in and out sometimes? A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven / Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption. Note: Please keep your phone and the master earphone (R) as close as possible to ensure a more stable Bluetooth connection.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: {1) This device may not cause harmful interference {2) this device must accept any interference received, including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
