Enable-IT 820P Pro Ethernet Extender Kit User Manual All Rights Reserved 1997 - 2013 ENABLE-IT - Proprietary and Confidential
Copyright © 1997-2013 Enable-IT, Inc. All rights reserved. No part of this documentation may be reproduced in any form, or by any means, or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from Enable-IT, Inc. Enable-IT, Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of Enable-IT, Inc., to provide notification of such revision or change. Enable-IT, Inc.
TABLE OF CONTENTS ABOUT THIS USER MANUAL ...................................................................................... 4 INTRODUCING THE 820P PRO ETHERNET EXTENDER KIT ........................................... 5 About The 820P Pro Ethernet Extender Kit ................................................. 5 Key Benefits ................................................................................................ 6 Summary Of Features .............................................................
ABOUT THIS USER MANUAL This product User Manual provides all the information needed to install and use the Enable-IT 820P Pro Ethernet Extender Kit. This User Manual is intended for use by technicians who are responsible for installing and setting up network equipment. Consequently, it is assumed that the installer has a basic working knowledge of LANs (Local Area Networks), PoE (Power-over-Ethernet) and voice telecom wiring.
INTRODUCING THE 820P PRO ETHERNET EXTENDER KIT Congratulations on purchasing the Enable-IT’s 820P Pro 820P Pro IP PoE Camera Extender Kit — the simplest method to stretch your broadband solutions for in-building deployment in commercial office buildings, hotels, and multi-tenant residential units. The 820P IP PoE Camera Extender Kit offers the Lowest Cost Solution in a simple design for rapid install using existing 4 pair Telco wiring.
Key Benefits The following list identifies the 820P Pro IP PoE Camera Extender Kit key benefits. Dramatic cost reduction over any competing technology. The Enable-IT 820P Pro IP PoE Camera Extender Kit requires no firmware and no maintenance Broadband technology that delivers in-building Ethernet access over 4 pair of existing Category 2, up to Category 5e, 6 or 7, wiring up to 800ft (244m), whether spare or actively in use for analog or digital voice. This means no new wiring is required.
Typical Use Applications Enable-IT 820P Pro IP PoE Camera Extender Kit are usually installed onto telephone wiring infrastructures where extension of backbone services is required and expensive fiber options are prohibitive. The 820P Pro Extended Ethernet Kit allows a standard Ethernet segment to be deployed quickly over existing 4 pair Telco Copper Wiring in combination with existing POTS voice signals. That is 572ft beyond standard Category rated Ethernet.
INSTALLING THE 820P PRO ETHERNET EXTENDER KIT The Enable-IT 820P Pro IP PoE Camera Extender Kit has a distance restriction of 800ft (244m) over existing Category 2, up to Category 5e, 6 or 7, wiring from device extension to device extension. Therefore quick, simple site surveys and installation planning are highly recommended. This chapter describes the recommended installation process for the Enable-IT 820P Pro Ethernet Extender Kit.
Network Configuration In some instances, your Ethernet switch, desktop computer, laptop, WiFi Access Point, or any LAN device not mentioned may need to be configured for 10Mbps auto-sensing as the 820P Pro is a 10Mbps Ethernet switch. It may be the case that your Ethernet switch is not passing data through the 820 Pro to your remote LAN device, therefore setting the LAN configuration on your device to 10Mbps will allow it to recognize the 820P Pro switch settings.
DO NOT INSERT ANY BLANK RJ-45 HEADS INTO ANY PORTS BEFORE CRIMPING – OTHERWISE YOU WILL RENDER THE PORT USELESS – BENT PINS Attach RJ-45 Male heads to your existing wiring and follow the diagram below. For data only use pins 1,2,3 & 6. For Data and PoE use all pins. PoE uses pins 4,5,7 & 8 Unpacking The Enable-IT 820P Pro IP PoE Camera Extender Kit Carefully remove the Enable-IT 820P Pro Kit’s packing materials from the box. Verify that the items listed below are present.
Follow the following diagram to create a T-568B standard connection between the 820P Pro and your end PoE LAN device. This wire run becomes your Ethernet backbone between the 820P Pro unit and your end PoE LAN device. The wire pair must be straight through and not have any connector blocks in-between the units. If you have a connector block, you must remove the 4-pair and bridge together with Telco wire butt clips.
Please ship Authorized RMAs to: Enable-IT Processing Facility 16600 Harbor Blvd, Suite I Fountain Valley, CA 92708-1363 Returning Products for Refund Enable-IT, Inc. offers a generous 45-Day refund on a single Ethernet Extender Kit only, and is subject to a 15% Restocking Fee. Shipments without a valid or authorized RMA number, or sent to our corporate Las Vegas address, can be refused and / or billed for additional shipping. ENABLE-IT, INC. LIMITED WARRANTY Enable-IT, Inc.
8:00 a.m. and 5:00 p.m. PST and otherwise fully comply with Enable-IT’s then-current RMA policy; (2) return the Product to Enable-IT in its original packaging freight pre-paid; and (3) provide to Enable-IT the original receipt or bill of sale establishing the date on which the Product was purchased. Products returned to Enable-IT without an RMA number will be returned to the End User. Enable-IT shall not be responsible for damage or loss during shipment of the returned Product to Enable-IT. d.
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO THE END USER. 3. LICENSE AND LIMITATIONS. The firmware and software embedded in the Product (the "Embedded Software") are licensed to you. Your use of the Product is your acceptance of the warranty terms above and the terms below. You may use the Embedded Software solely in conjunction with your use of the Product.
