Phau Ntawv Qhia

ManualsBrandsEMX INDUSTRIES ManualsAccess ControlEMX INDUSTRIES CellOpener-365 GSM Access Control

EMX Industries, Inc. Tech support: 1216-518-9889 1/16

Document Number 10370104 Rev 1.1 technical@emxinc.com

CellOpener-365

GSM Access Control

With Yearly & Weekly Timer

Instruction Manual

This GSM access control system allows up to 2000 registered users to operate any garage door /

gate using their phone with no cost for the call to the user. This simple to use access control

system uses a GSM SIM card that must be activated upon installation. Simply dial the associated

phone number for the SIM Card from any phone or mobile-phone and the gate will open

without any cost of a call to you and with no limit of rage. The CellOpener-365 also allows for an

input contact to be used to trigger a custom-made SMS text message to a property manager

letting him know that someone is at the gate or door.

In addition, the unit offers Weekly Timer and 365 Day Timer capability to offer maximum

security and allow a property manager to prevent (or enable) the gate or overhead door from

opening (or stay close) on certain days and times such as national holidays or special events.

The current date and local time is automatically set via the GSM network so there is never a

reason to even make adjustments for daylight savings time.

All the programming of the CellOpener-365 is done by simple SMS text commands. This feature

allows programming to be done remotely from anywhere in the world making life easy for

maintenance, security and HR staffs that need to enable or disable an individual person’s access

to a site within a second.

Power 12V – 18V AC or DC

Standby Current–LEDs enabled

0.2A @ 12 VDC / 0.3A @ 24VDC

Standby Current-LEDs disabled 0.1A @ 12 VDC / 0.15A @ 24 VDC

Max Authorized Users 1600 Normal Users and 400 Special Users

Relay Contact Rating 5A @ 24V

Operating Temperature Min -40°C / Max 65°C

Antenna Cable Length 3m’ (118.2 inches)

Lead Cable Length 0.5m’ (19.7 inches)

Specifications

Summary of content (16 pages)

PAGE 1
CellOpener-365 GSM Access Control With Yearly & Weekly Timer Instruction Manual This GSM access control system allows up to 2000 registered users to operate any garage door / gate using their phone with no cost for the call to the user. This simple to use access control system uses a GSM SIM card that must be activated upon installation. Simply dial the associated phone number for the SIM Card from any phone or mobile-phone and the gate will open without any cost of a call to you and with no limit of rage.
PAGE 2
Wiring Connections 1. Power Make sure to insert the SIM card and connect the Antenna before you power-up the unit. Do not attach the unit’s antenna to any metal surface. The unit can operate with voltage between 12V to 18V AC or DC using the black and red wires. If DC power is used, the BLACK wire is the negative and the RED wire is the positive. 2. Memory The unit can hold up to 1600 authorized users and up to 400 limited users, total of 2000 users.
PAGE 3
Please Note!  The caller’s ID of the users must be ON (not private) in order for the CellOpener-365 unit to identify the user when calling the system to gain access.  For solar applications, to reduce the current consumption of the unit, you can remove the jumper link on the right-hand side in the unit, to turn off the LEDs after the installation is complete. See diagram above. Programming Please make sure that the mobile phone you are using to program this unit has its Caller ID ON.
PAGE 4
THIS IS A WARNING. Do you wish to DELETE all the phone numbers? If you wish to proceed, confirm by sending “YES” in all capital letters: YES The unit will send back SMS that says: All phone numbers were deleted *Note: Ignoring the warning message and not replying “YES” within two minutes, will cause the unit to disregard the last command and the phone numbers would be saved and not be deleted. 3.
PAGE 5
Confirming: The number 13308317452 allowed unlimited entries on Sundays Mondays Saturdays between 9:00AM and 5:00PM b. The following SMS message is an example of how to allow a limited number of entries with no limit for times or days of the week for a special number: 9999AS.12168317435.3.0900.1700.1234567 9999 AS 12168317435 3 0900.
PAGE 6
The factory default setting for the relay is a MOMENTARY function (with a 1 second PULSE).
PAGE 7
. How to check if the Unit’s Relay is ON or OFF You can check the current status of unit’s relay by SMS command as follows: *Note: 9999 Is the password (default password 9999) 9999relay The unit will reply by SMS according to the current status of the relay. If the relay is OFF the SMS reply would be: The relay is OFF If the relay is ON the SMS reply would be: The relay is ON 8.
PAGE 8
10. How to check the Number of Users in the System The system can be programmed with 1600 Normal Users and 400 Special Users. You can check the number of users in the system by sending SMS: *Note: 9999 Is the password (default password 9999) 9999users The unit will reply by SMS: There are #### normal users and ### special users in the system 11. How to LOCK / UNLOCK the system The unit can be LOCKED, so that none of users can use the system and activate the relay.
PAGE 9
To cancel the Hold Command send SMS as follows: 9999release The unit will reply by SMS: Hold Command is OFF 13. OPEN TO ALL Command The unit can be programmed so that it will open the gate to ANY incoming call (without checking if the caller is an authorized user).
PAGE 10
YES The unit will confirm by SMS: The unit was set to factory default *Note: Ignoring the warning message and not replying “YES” within two minutes, will cause the unit to disregard the defaulting command. 15. How to change the Password The factory default password is 9999 and it can be changed by sending the following SMS message where “####” correspond to the new password: 9999password#### The unit will confirm by SMS reply: The new password is # # # # 16.
PAGE 11
Example: 9999RS.The Alarm is ON.The Alarm is OFF. 9999 RS . Default password Status input-1 Delineates between the functions The NEW SMS reply message when the status input is connected to ground. The Alarm is ON The SMS reply message when the status input is not connected to ground. The Alarm is OFF 18. INPUT - 2: Alert This input can be used to ALERT someone on their mobile phone each time input-2 is triggered. This can be used as a DOORBELL or ALERT the user each time the gate opens.
PAGE 12
Programming Weekly & Yearly Timer Weekly Timer This smart system will automatically set its local time, day of the week and the date as soon as it is powered up. Moreover, it will also correct the local time in the unit when Daylight Time Savings occurs twice a year. The weekly timer can be set to turn ON and OFF the internal relay on certain days and at certain time intervals.
PAGE 13
TUE, WED, THU between 8:00AM and 13:00PM FRI between 7:30AM and 15:00PM That means: The relay of the weekly timer will turn ON at 09:00AM and turn OFF at 17:00PM on every Sunday, Monday, and Saturday. Also, it will turn ON at 08:00AM and turn OFF at 13:00PM each Tuesday, Wednesday and Thursday. And turn ON at 07:30AM and OFF at 15:00PM each Friday. *Note: The following SMS command is wrong: 9999WT.0900.1700.127,0800.1300.234,0730.1500.6 This is because the command contains two time intervals for MONDAY. b.
PAGE 14
Or for example: The Weekly Timer is ON: Sunday, Monday, Saturday, between 9:00AM and 17:00PM 3. How to clear the settings of Weekly Timer: Send SMS: 9999WT.clear The unit will delete the current settings of the weekly timer and reply by SMS message as follows: No events are recorded for the Weekly Timer Yearly Timer The Yearly Timer can be programmed to overtake control of the weekly timer and turn ON or OFF the relay output on certain days at certain times.
PAGE 15
The unit will reply by SMS that says: Confirming: Yearly Timer OFF: 01.09.21, from 07:00AM until 02.09.21 13:00PM Another example: 9999YT.050122.0000.050122.2400.ON The unit will reply by SMS that says: Confirming: Yearly Timer ON: 05.01.22, 00:00AM until 05.01.22, 24:00PM *Note: During the interval time when the relay is OFF (not active) the unit will respond to incoming calls of the users and will trigger the relay according to the setting.
PAGE 16
3. How to Clear All the Yearly Timer’s Settings & Events Send SMS: 9999YT.clear The unit will reply by SMS that says: No events are recorded for the Yearly Timer END. EMX Industries, Inc. Document Number 10370104 Rev 1.1 Tech support: 1216-518-9889 technical@emxinc.