Emulex Drivers, Software and Manuals LP850 Installation and Reference Manual Table of Contents Installation Compatibility Prerequisites Install HBA Attach Media Apply Power View LEDs Reference Specifications DB9 Pinout FCC and Regulatory Notices Declaration of Conformity Laser Safety 1
Emulex Drivers, Software and Manuals Chapter 1 − Installation Table of Contents Compatability Prerequisites Install HBA Attach Media Apply Power View LEDs 2
Emulex Drivers, Software and Manuals Installation Caution Emulex LightPulse Host Bus Adapters (HBAs) contain electronic components that can be damaged by static electricity through an electrostatic discharge (ESD) event. To prevent ESD damage, maintain frequent contact with any grounded metal surface. A grounding wrist strap is useful for this purpose. Handle the card carefully at all times and preferably by the edges.
Emulex Drivers, Software and Manuals Install the Host Bus Adapter Board 1. Record IEEE and serial numbers. Each host bus adapter port is shipped with a unique address identifier called the IEEE address. Since this adapter has two ports, there are two IEEE addresses. The IEEE address is used when configuring your system. The serial number is used when communicating with Emulex. All numbers are clearly marked on the board. We recommend that you record these numbers before installing the adapter. 2.
Emulex Drivers, Software and Manuals Attach Media Attach fibre optic or copper cable to the host bus adapter. Attach Fiber Optic Cable (Multi/Single Mode) Note The host adapter will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode.) Use multimode fiber optic cable, that adhere to the following specifications: Fiber Optic Cable Maximum Length Minimum Length Connector 62.
Emulex Drivers, Software and Manuals Attach Copper Duplex Cable Use copper Twinax or Quad Axial cable that adheres to the following secifications: Cable Type Maximum Length Data Rate Connector Twinax or Quad Axial 30 meters 1.0625 Gb/s DB9 1. Connect the copper duplex cable to the DB9 connector on the host adapter board as shown. 2. Connect the other end of the cable to the Fibre Channel device. After the media is connected to the host adapter, you are ready to apply power to the computer.
Emulex Drivers, Software and Manuals Apply Power 1. Verify that the host adapter is securely installed in the computer. 2. Verify that correct media is attached. 3. Plug in and turn on computer. 4. Observe LEDs for Power On Self Test (POST) results. View LEDs Green and yellow display lights (LEDs) can be seen through openings in the host adapter's mounting bracket. Green indicates power and yellow signifies port activity. POST conditions and results are summarized in this table.
Emulex Drivers, Software and Manuals Chapter 2 − Reference Table of Contents Specifications DB9 Pinout FCC and Regulatory Notices Declaration of Conformity Laser Safety 8
Emulex Drivers, Software and Manuals Specifications Parameter Range Hardware Interface 20 pin connector for GBIC models Physical Dimensions Short PCI form factor 6.88" x 4.20" Power Requirements 11 watts @ + 5.0 VDC (typical) Airflow 100 lfm minimum Temperature Operating:K2° to 113°F (0° to 45°C) Storage:I4° to 131°F (−10° to 55°C) Humidity 5% to 95% non−condensing Agency Approvals for LP850−D1 UL recognized to UL1950 CUR recognized to CSA22.2, No.
Emulex Drivers, Software and Manuals Reference Copper Port (DB9) Pinout This pinout applies to embedded copper ports.
Emulex Drivers, Software and Manuals FCC and Regulatory Notices Class 1 Information Label CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A` LASER DE CLASSE 1 The above statement applies to products marketed in the European Union. FCC and VCCI Model LP850−D1 (Copper Model) This device complies with Part 15 of the FCC Rules.
Emulex Drivers, Software and Manuals FCC Compliance Information Statement; Models LP850−T1/N1 (GBIC Models) FCC Compliance Information Statement; Model LP850−F1 (1 X 9) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Emulex Drivers, Software and Manuals • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The reader is cautioned that any changes or modifications to the equipment not expressly approved by Emulex could void the user’s authority to operate this equipment.
Emulex Drivers, Software and Manuals Model LP850−D1 (Embedded Copper Model) Product Label Translation: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. VCCI—A Manual Notice Translation: This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI).
Emulex Drivers, Software and Manuals Declaration of Conformity This Declaration identifies the product, manufacturer’s name and address, and applicable specifications recognized in the European Union. DECLARATION OF CONFORMITY Manufacturer: Emulex Corporation 3535 Harbor Blvd.
Emulex Drivers, Software and Manuals European Union This equipment complies with CISPR22/EN55022 Class A. Warning This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Declaration of Conformity This Declaration identifies the product, manufacturer’s name and address, and applicable specifications recognized in the European Union. DECLARATION OF CONFORMITY Manufacturer: Emulex Corporation 3535 Harbor Blvd.
Emulex Drivers, Software and Manuals Laser Safety Notice This laser safety information contains certification and product information covering laser products known as optical Gigabaud Link Modules (GLMs), Gigabit Interface Converters (GBICs), 1x9 and small form factor transceivers sold as accessories to or incorporated in Emulex LightPulse host adapters. The GLM, GBIC, 1x9 and small form factor transceiver are the primary cable connection mechanisms for any optical port on the host adapter and hub.
Emulex Drivers, Software and Manuals In Europe, all optical GLMs, GBICs, 1x9 and small form factor transceivers sold by Emulex are certified as Class 1 laser component assemblies that conform to the requirements contained in the CENELEC (European Committee for Electrotechnical Standardization) standard EN60825−1:1994 (including amendment 11) and EN60825−2:1994.
Emulex Drivers, Software and Manuals Product Information GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver GLM The optical GLM is a single port communications card. Each communication port consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains a semiconductor laser diode of gallium aluminum arsenide (GaAlAs).
Emulex Drivers, Software and Manuals maintenance, service operations or adjustments can be performed the GBIC. Small Form Factor Transceiver The small form factor transceiver is an integrated duplex data link for bi−directional communications over multimode or single mode optical fiber. Each small form factor transceiver consists of a transmitter and receiver optical subassembly.
Emulex Drivers, Software and Manuals GLM The GLM is designed and certified for applications using point−to−point optical fiber links only. Use of the product with multiple input or multiple output optical links (for example, star couplers) is prohibited since it is incompatible with the GLM’s certification. The GLM will not allow normal data transmission on the optical link unless it is connected to another similar GLM or compatible laser product.
Emulex Drivers, Software and Manuals Class 1 laser product. Any system level product that incorporates the small form factor transceivers must provide power supply protection that guarantees a voltage of 5.0 volts or less at the small form factor transceivers. The functional power supply range of the small form factor transceivers product is specified as 3.135 to 3.465V typically. Operation outside of this range may degrade the performance and lifetime of the transceiver.
Emulex Drivers, Software and Manuals System Level Certification All GLMs and GBICs sold as accessories by Emulex or host adapters containing embedded 1x9 or small form factor transceivers are certified as Class 1 laser products within the U.S. and Class 1 laser component assemblies outside of the U.S. Manufacturers of products properly incorporating the GLM, GBIC, 1x9 or small form factor transceiver do not need to recertify their product for laser safety.
