Emulex Documentation, Drivers and Software LP1050DC Installation and Reference Manual Table of Contents Installation Features Compatibility Prerequisites Install HBA Attach Media Apply Power View LEDs Reference Specifications FCC Statement Declaration of Conformity Laser Safety 1
Emulex Documentation, Drivers and Software Installation Features The LP1050DC host bus adapter offers a highly integrated 2Gb/s Fibre Channel HBA for use in servers based on either the conventional PCI or PCI-X 1.0a expansion bus architectures. The LP1050DC delivers exceptional performance through the use of a sixth generation Emulex Thor controller.
Emulex Documentation, Drivers and Software Prerequisites ● ● ● ● PCI/PCI-X 32- and 64-bit data and addressing PCI bus computer with a clock rate up to 66 MHz PCI-X bus computer with a clock rate up to 133 MHz Media and connectors copyright © - Emulex Corporation - all rights reserved - 2003 3
Emulex Documentation, Drivers and Software Install the Host Bus Adapter Board Caution Emulex LightPulse® Host Bus Adapters (HBAs) contain electronic components that can be damaged by static electricity through an electrostatic discharge (ESD) event. To prevent ESD damage, maintain constant contact with any grounded metal surface. A grounding wrist strap is useful for this purpose. Handle the card carefully at all times and preferably by the edges.
Emulex Documentation, Drivers and Software Note The host bus adapter comes with a standard PCI bracket installed. The low-profile mounting bracket is shorter than the standard bracket; approximately 3.11 in. (7.9 cm) compared to 4.75 in. (12.06 cm) long. If you need a low-profile bracket, contact Emulex Product Information by phone at 800-EMULEX-3 (800-368-5393) or 714-885-3450, or by e-mail at info@emulex.com. A low-profile bracket will be shipped within one business day. 5.
Emulex Documentation, Drivers and Software Attach Media Note The host bus adapter (HBA) will not allow normal data transmission on an optical link unless it is connected to another similar or compatible laser product (that is, multimode to multimode.) Use multimode fiber optic cable, with short-wave lasers, that adheres to the following specifications: Fiber Optic Cable Maximum Length Minimum Connector Length 62.5/125 µm (multimode) 300 meters at 1.0625 Gb/s 150 meters at 2.
Emulex Documentation, Drivers and Software Apply Power 1. 2. 3. 4. Verify that the host bus adapter is securely installed in the computer. Verify that the correct media is attached. Plug in and turn on the computer. Observe LEDs for Power On Self Test (POST) results. View LEDs Green and yellow LEDs can be seen through openings in the host bus adapter's mounting bracket. Green indicates power and yellow signifies port activity. Each port has a corresponding set of green and yellow LEDs.
Emulex Documentation, Drivers and Software ON ON Failure while functioning Slow blink ON Normal operating condition - 1 GHz link rate Fast blink ON Normal operating condition - 2 GHz link rate OFF Slow blink Normal - link down or not yet started Slow blink Slow blink Offline for download Fast blink Slow blink Restricted offline mode (waiting for restart) Flashing Slow blink Restricted offline mode, test active *A light-emitting diode (LED) is located near the top edge of the board.
Emulex Documentation, Drivers and Software Reference Specifications Parameter Media Interface Range The Thor controller interfaces to the physical media through an FC-0 Media Interface (FC-PI compliant transceiver), and then connects through a single optical fiber LC connector. Low-profile MD2 form factor, 6.600 inches by 2.536 inches, Physical Dimensions and accommodates both the full-height and low-profile bracket. In a PCI/PCI-X, 66-MHz host: ● ● ● Power Requirements 2.0 watts (typical) @ +3.
Emulex Documentation, Drivers and Software FCC and Regulatory Notices CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A` LASER DE CLASSE 1 LP10000DC-M2, LP10000-M2, LP1050DC-F2 and LP1050-F2 Models This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Emulex Documentation, Drivers and Software Notice for Japan and Translations (VCCI) Product Label This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. VCCI—A Manual Notice Translation: This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI).
Emulex Documentation, Drivers and Software Notice for South Korea and Translations (MIC) Translation: Class A Equipment: Please note that this equipment has been approved for business purposes with regards to electromagnetic interference. If purchased in error for use in a residential area, you may wish to exchange the equipment where you purchased it.
Emulex Documentation, Drivers and Software Declaration of Conformity LP10000DC-M2, LP10000-M2, LP1050DC-F2 and LP1050-F2 Models This equipment complies with CISPR22/EN55022 Class A. Warning This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Note Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment.
Emulex Documentation, Drivers and Software 14
Emulex Documentation, Drivers and Software Laser Safety Notice This laser safety information contains certification and product information covering laser products known as optical Gigabaud Link Modules (GLMs), Gigabit Interface Converters (GBICs), 1x9 and small form factor transceivers sold as accessories to or incorporated in Emulex LightPulse host adapters. The GLM, GBIC, 1x9 and small form factor transceiver are the primary cable connection mechanisms for any optical port on the host adapter and hub.
Emulex Documentation, Drivers and Software In the United States, all optical GLMs, GBICs, 1x9 and small form factor transceivers sold by Emulex are certified as Class 1 laser products that conform to the requirements contained in the Department of Health and Human Services (DHHS) regulation 21 CFR subchapter J. The certification is indicated by a label located on the optical GLM, GBIC, 1x9 or small form factor transceiver.
Emulex Documentation, Drivers and Software Product Information GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver GLM The optical GLM is a single port communications card. Each communication port consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains a semiconductor laser diode of gallium aluminum arsenide (GaAlAs).
Emulex Documentation, Drivers and Software GBIC The optical GBIC is an integrated duplex data link for bi-directional communications over multimode or single mode optical fiber. Each GBIC consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains a semiconductor laser emitting in the wavelength range of 770 to 860 nanometers for shortwave length GBICs and 1270 to 1355 nanometers for long wavelength GBICs.
Emulex Documentation, Drivers and Software Usage Restrictions Failure to comply with these usage restrictions may result in incorrect operation of the system and could possible lead to points of access that may emit laser radiation levels above the Class 1 limits established in the U. S. by the DHHS and within Europe by EN60825-1/EN60825-2. GLM GBIC 1 x 9 Transceiver Small Form Factor Transceiver GLM The GLM is designed and certified for applications using point-to-point optical fiber links only.
Emulex Documentation, Drivers and Software 1 x 9 Transceiver Short wavelength 1x9 transceivers allow normal data transmission on the optical link when they are connected to another compatible laser product. Short wavelength 1x9s embedded in Emulex host adapters are non-OFC. For non-OFC links, a compatible laser device must be non-OFC and certified as a Class 1 laser product.
