Installation & Programming Guide EMTouch Electronic Lever Locksets ASSA ABLOY, the global leader in door opening solutions
What’s in the Box 4a 4b 5 4c 2 4d 3 1 4 6 7 6 8 ITEM NO. 1 2 Latch Assembly 2 3/8” or 2 3/4” Backset 4a 4b 4c 5 6 7 8 2 DESCRIPTION Outside Trim Plate Assembly 3 4 Key 4d Inside Trim Plate Assembly Inside Chassis Inside Trim Plate #8-32 x 3/8" Flat Head Machine Screw 9V Alkaline Battery #8-32 x 11/2" Flat Head Machine Screw #8 x 3/4" Wood Screw Strike Plate Plastic Extender QTY.
Preparation 1. Confirm Handing HANDING OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE In-Swing Doors outside Hinge is on the left. Door is Left Hand (LH). Out-Swing Doors Hinge is on the right. Door is Right Hand (RH). Hinge is on the left. Door is Left Hand (LH). outside Hinge is on the right. Door is Right Hand (RH). 2. Door Prep 2 3/8” or 2 3/4” Backset 1/8” Deep 2 1/4” 2 1/8” Diameter Bore 1“ 3. Remove Screws from Inside Trim Plate 3.
How to Install 1. Install Strike Plate & Latch Step 1: Fasten Strike Plate using two #8 x 3/4” Wood Screws (item #6). Step 2: Fasten Latch using two #8 x 3/4” Wood Screws (item #6). 2. Remove Screws from Inside Trim Plate Use a Phillips head screwdriver to remove screws (item #4c) shown below and detach Inside Trim Plate from the Inside Chassis. ! REMOVE INSIDE CHASSIS FROM TRIM PLATE BEFORE INSTALLING THE OUTSIDE TRIM. THUMBTURN MUST BE IN LOCKED POSITION.
3. Install Outside Trim Plate Assembly Step 1: While holding Outside Trim Plate Assembly, Press the Plastic Extender (A) into end of Spindle Shaft (B). The Shaft is properly aligned when the marking ‘TOP’ can be seen from an overhead view. ! THIS SIDE ON TOP. B A Step 2: Position the Outside Trim Plate Assembly through the bore hole. ! ONCE POSITIONED, OUTSIDE TRIM PLATE ASSEMBLY REQUIRES SUPPORT. Feed wire harness through the bore hole. Fit Plastic Extender through latch.
4. Install Inside Chassis Step 1: Confirm the position of Cam Link. ! For Right Hand Locks: Turn to right position. CAM LINK MUST REMAIN IN THE CORRECT POSITION DURING INSTALLATION. For Left Hand Locks: Turn to left position. Step 2: Feed the Wire Harness through Inside Chassis.
Step 3: Fasten Inside Chassis using two #8-32 x 11/2” Flat Head Machine Screw (item #5). ! CHECK ALIGNMENT BEFORE FULLY TIGHTENING SCREWS. Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B). A B Step 5: Install Battery. 9V Battery For optimal performance, always use a good quality battery.
5. Install Inside Trim Plate Fasten Inside Trim Plate using two #8-32 x 3/8” Flat Head Machine Screws (item #4c). ! USER CODES ARE LOCATED ON THE INSIDE TRIM PLATE & ON PAGE 11. ! Inside Correct for installation Incorrect for installation *Locked - requires code Unlocked *Locked position is required for installation and removal of the Inside Trim Plate Assembly. (Does not apply to Keypad Storeroom/Gate product) ! THUMBTURN MUST BE IN LOCKED POSITION FOR INSTALLATION.
How to Use Your Lock is Ready to Use Your Emtek lock is shipped with two 4-digit user codes and a 6-digit programming code. These codes are randomly generated at the factory. (Turn to next page for Programming Instructions.) To Unlock: 1. Press EMTEK key or touch 3 fingers across screen. 2. Enter 4-digit user codes. 1 2 3 (See sticker located on the inside trim plate or on page 11). 3. Turn Handle.
How to Program Programming Your Lock In order to perform each of the following six functions, the lock must first be placed in Programming Mode: 1. 2. 3. 4. 5.
Keypad Operation - Beeper & LED Indicators Function Indicators Valid Code • 1 short beep, EMTEK button flashes Green.
Scan for how to install videos. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. Copyright © 2011, Emtek Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Emtek Products, Inc. is prohibited.
