Installation & Programming Guide EMTouch™ & EMTouch™ Classic Style Electronic Lever Locksets EMTouch™ EMTouch™ Classic Style ASSA ABLOY, the global leader in door opening solutions
What’s in the Box 4a 4b 5 4c 2 4d 3 1 9 4 6 7 6 8 ITEM NO. 1 2 Outside Trim Plate Assembly 3 4 Adjustable Latch for 2 3/8” or 2 3/4” Backset 4a 4b 4c 5 6 7 8 9 2 DESCRIPTION Key 4d Inside Trim Plate Assembly Inside Chassis Inside Trim Plate #8-32 x 3/8" Flat Head Machine Screw 9V Alkaline Battery #8-32 x 11/2" Flat Head Machine Screw #8 x 3/4" Wood Screw Strike Plate Plastic Extender Plastic Latch Pin QTY.
Preparation 1. Confirm Handing HANDING OF DOOR IS ALWAYS DETERMINED FROM THE OUTSIDE In-Swing Doors outside Hinge is on the left. Door is Left Hand (LH). Out-Swing Doors Hinge is on the right. Door is Right Hand (RH). 2. Door Prep Hinge is on the left. Door is Left Hand (LH). outside 3. Door Jamb Prep 2 3/8” or 2 3/4” Backset 1/16” Deep Hinge is on the right. Door is Right Hand (RH). 4.
How to Install 1. Install Adjustable Latch Fasten Adjustable Latch using two #8 x 3/4” Wood Screws (item #6). To remove Pin: Push Plastic Latch Pin (item #9) through latch with screwdriver. Scan QR code for installation video ! Plastic Latch Pin Plastic The Adjustable Latch is factory Latch shipped with a 23/4” backset Pin position. Remove pin and slide spindle hub forward for a 23/8” backset, then reinsert the pin in the hole at the back of the latch as shown. 2.
3. Install Outside Trim Plate Assembly Step 1: While holding Outside Trim Plate Assembly, Press the Plastic Extender (A) into end of Spindle Shaft (B). The Shaft is properly aligned when the marking ‘TOP’ can be seen from an overhead view. ! THIS SIDE ON TOP. B A Step 2: Position the Outside Trim Plate Assembly through the bore hole. ! ONCE POSITIONED, OUTSIDE TRIM PLATE ASSEMBLY REQUIRES SUPPORT. Feed wire harness through the bore hole. Fit Plastic Extender through latch.
4. Install Inside Chassis Step 1: Confirm the position of Cam Link. ! For Right Hand Locks: Turn to right position. CAM LINK MUST REMAIN IN THE CORRECT POSITION DURING INSTALLATION. For Left Hand Locks: Turn to left position. Step 2: Feed the Wire Harness through Inside Chassis.
Step 3: Fasten Inside Chassis using two #8-32 x 11/2” Flat Head Machine Screw (item #5). ! CHECK ALIGNMENT BEFORE FULLY TIGHTENING SCREWS. Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B). A B Step 5: Install Battery. 9V Battery For optimal performance, always use a good quality battery.
5. Install Inside Trim Plate Fasten Inside Trim Plate using two #8-32 x 3/8” Flat Head Machine Screws (item #4c). ! USER CODES ARE LOCATED ON THE INSIDE TRIM PLATE & ON PAGE 11. Inside ! Scan QR code for installation video Correct position for installation.Thumbcam must be positioned as shown (Neutral Position)* *Neutral position is required for installation and removal of the Inside Trim Plate Assembly.
How to Use Your Lock is Ready to Use Your Emtek lock is shipped with two 4-digit user codes and a 6-digit programming code. These codes are randomly generated at the factory. (Turn to next page for Programming Instructions.) To Unlock: 1. Press EMTEK key or touch 3 fingers across screen. 2. Enter 4-digit user codes. 1 2 3 (See sticker located on the inside trim plate or on page 11). 3. Turn Handle.
How to Program Programming Your Lock In order to perform each of the following six functions, the lock must first be placed in Programming Mode: 1. 2. 3. 4. 5.
Keypad Operation - Beeper & LED Indicators Function Valid Code Invalid Code/Access Denied* Lock-Out Mode Error Indicators • 1 short beep, EMTEK button flashes Green.
Scan QR code for installation video ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. Copyright © 2013, Emtek Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Emtek Products, Inc. is prohibited.
