EMPowered™ Motorized Smart Lock Upgrade - Connected by August Sectional Entry Set Download and install Home app
What’s in the box 6 1a 5 4 1 8 7 14 9 1c 1d 1b 10 1f 1g 1e 2 3 14 18 14 19 11 17 ITEM NO. 1 1a 1b 16 DESCRIPTION EMPower Unit August Module Battery Cover QTY. ITEM NO. 1 7 1 1 Passage Latch 1 1 1 1 1 1 2 12 13 #8-32 Flat head Machine Screw Threaded Washer 1 1 Mounting Plate 1 Interior Knob/Lever Assembly 1 15 16 17 1e 1f Interior Escutcheon #10-32 x 2-1/8” Machine Screws 1g 2 6 9 Deadbolt Cylinder QTY.
23/8” or 23/4” Door Prep 2-3/8" or 2-3/4" 1" Dia. Edge Bores 21 21/4” 4" 21/8” Dia. Bores 2-1/8" Dia.
1 Install Latches ! Note: Use only the supplied latch for proper functionality.
2 Install Grip and Interior Lever/Knob 5
3 Remove Battery Cover Loosen screw on bottom to remove cover.
4 Install Lock Cylinder & Interior Mounting Plate ! Must use screw guide Extension Collar required for thin doors 7
5 Check Interior Mounting Plate Alignment ! Center tail piece in mounting plate hole before tightening.
6 Install Interior Escutcheon ! Bolt must be in retracted (unlocked) position 9
7 10 Testing Operation
8 Install Batteries ! Bolt must be in retracted (unlocked) position before installing batteries.
9 Handing the Lock To hand the lock, press the button until you hear one beep 12
10 Go to the August App to Complete Installation Set Up a Device - EMTEK SMART LOCK SET UP MY FIRST DEVICE SET UP A LOCK CONNECTED BY AUGUST SET UP AN EMTEK SMART LOCK 13
Installing DoorSenseTM with Connected by August Locks - Surface Mount Option DoorSenseTM Cover Mounting Screws 1.
Installing DoorSenseTM with Connected by August Locks - Surface Mount Option 2. Attach mounting tape then screw into frame 3.
Installing DoorSenseTM with Connected by August Locks - Flush Mount Option DoorSenseTM Housing DoorSenseTM Cap 1.
Installing DoorSenseTM with Connected by August Locks - Flush Mount Option 2. Drill hole and Insert DoorSenseTM 5/8” Diameter 1/2” Deep 3-1/2” 3-1/2” 3.
Go to the August App to Complete Installation Set Up a Connect Hub GO TO MENU 18 SET UP A DEVICE SET UP A CONNECT
11 Install Cover Secure cover by tightening screw on bottom.
Hardware Troubleshooting Cycle lock in both the locked and unlocked positions. If problems are found: Symptom Door is binding Suggested Action • Check that door and frame are properly aligned and door is free swinging. • Check hinges: They should not be loose or have excessive wear on knuckles. Bolt will not deadlock • Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by increasing the depth of the pocket for the bolt.
Programming Troubleshooting Symptom Suggested Action Lock does not respond - door is open and accessible. • Check batteries are installed and oriented correctly (polarity) in the battery case. Lock does not respond - door is locked and inaccessible. • Batteries may be completely discharged. Unit is on for a while then shows no reaction. • Check batteries are in good condition; replace batteries* if discharged. • Use your physical key to unlock the door. • Batteries do not have enough power.
Resetting Lock to Factory Default When lock is reset to factory defaults, all programming features are reset to original default settings (see below). 1. Remove battery cover and batteries. 2. Remove the interior escutcheon to access the reset button. 3. The reset button (see image) is located beside the PCB cable connector. 4. While pressing the reset button (Minimum of 3 seconds) reinstall batteries. Release reset button. 5. Replace battery cover.
Compliance FCC INTERFERENCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IN8-EMPCYLSECT REV 19A 11-05-19 Copyright © 2019, EMTEK Products, Inc. an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of EMTEK Products, Inc. is prohibited. ! WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
