User guide

No need to select the TV mode.
 SHIFT+Volume+/-:menunavigationkeys,allowyoutonavigate
left and right into the menu of your appliances.
[9] Teletext MIX: Allows to mix the Teletext and the picture of the
selected channel.
[10]Mute:Allowsyoutoturnon/offthesound.Youcancontrolthe
«Mute» function of your TV even when you are in VCR, DVD or SAT
mode. No need to select the TV mode.
 SHIFT+Mute:OKkey,conrmstheselection.
[11] Teletext OFF:
TV mode: Stop Teletext.
 SHIFT+TeletextOFF:ExitMenu.
[12] Teletext Hold: Stop page change in Teletext mode.
[13]Numerickeys0-9:Workthesamewayasyouroriginalremote.
[14] Teletext ON:
 TVmode:Start/stopTeletext.
 SHIFT+TeletextON:MenuON.
[15] ENT: If you are in programming mode – automatic code
search-youcanconrmthecodeofthedeviceyouwanttocontrol.In
connectionwiththenumerickeys,thisbuttonallowsyouwithsome
equipment to select directly channels higher than 9.
[16]A/V:Selectionofanexternalsource(SCARTinput).
[17] Play, FF, Stop, Rew, Pause:
 InVCR&DVDmode:Thesebuttonsworkthesamewayasin
your original remotes.
 InTVmode:Fasttextfunction(colouredkeys).
 REC(record):Thiskeyworksthesamewayastheoneonyour
originalremoteforyourVCR.Inordertoavoidamistakeyouhaveto
pressthiskeytwicetoactivatethisfeature.
4) Programming your TV, VCR, DVD and SAT modes
Note: You can dedicate any appliance (TV, DVD, SAT...) to the VCR,
DVD,orSATkeys:youjustneedtoenterthe4digitcode(foundin
thecodebook)oftheappliance,i.e.aVCRcodeundertheSATkey.
In any case, follow the steps below:
1. Makesureyourequipmentisswitchedon(forexampleTV).
2. PressandholdtheSETUP(4)keyuntiltheLEDindicator(1)lights
continuously.ReleasetheSETUPkey.
3. Pressandreleasethemodekey(3)ofthedeviceyouwantto
control (for example TV).
4. Enterthe4digitcode(13)fromtheCodeBook.TheLED(1)turns
off after the last digit is entered. If you entered a wrong code the LED
blinksfor3secondsandthengoesoff.Youhavetorepeatfromstep2.
5. Point the remote in the direction of your TV and press the POWER
button(2).Yourdeviceshouldturnoff.Checkotherfunctions(for
example for a VCR: FF or REW etc.). If certain functions are not
responding this indicates that the entered code is not the correct one.
In that case repeat the above procedure with the next corresponding
code of your brand.
6. Repeat this procedure from step 1 for the other equipment you want
to control (TV, VCR, DVD, SAT)
5) Manual code search
If your equipment (TV, SAT etc....) does not respond, try the other
codes for your brand. If it still doesn’t respond, try the Code Search
method.
Note: As you can dedicate any appliance (TV, DVD, SAT...) to the
VCR,DVDorSATkeys,youneedrsttoenterany4digitcodefor
thekindofapplianceyouwishtocontrol(foundinthecodebook),
i.e.:IfyouwanttoprogramaSATundertheVCRkey,enteranySAT
codefoundinthecodebookandthenfollowthestepsbelow:
1. Makesureyourequipmentisswitchedon.Ifnotswitchiton
manually.
2. Press and hold SETUP (4) until the LED indicator lights steadily.
Release SETUP
3. Pressthemodekey(3)thatmatchestheequipmentyouwantto
control (for example TV).
4. PressPROG+(7)repeatedlyuntilthePROGchanges.Ifyoustep
pastthecorrectcodeusePROG-(7)togobacktotherightcode.
5. When the equipment you want to control reacts press ENT (15) to
conrmthecode.That’sall.
Note:Ifyourequipmentdoesn’thavePROG+,youcanusePLAY
(VCRorDVD)(17)orPOWER(2)key.
The search starts after the last registered code. If that was 0030, the
search starts at 0031 until the last possible code and then goes from
0000 to 0029.
Note: if certain functions of your equipment can’t be controlled you
havetondadifferentcodeforyourbrand.
6) Automatic code search
Whensearchinganunknowncode,youcanstepthroughthelibrary
automatically (AutoSearch). When your equipment responds, you can
stop the searching process and store the code you found.
GB