Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
APPENDIX C – CHECKLISTS
1. Installation Checklist
Aircraft Identification:
DateSignatureName
Installation/Checks completed by:
Approved/Witnessed by:
Value√NAItemParameterSection
If the system is not wired to another
aircraft system, an installer provided
maintenance panel is required.
ApplicabilityMaintenance Panel
System available (Modman MP13E)
connected to a lamp.
Discrete
output
connections
Data link available (Modman MP13F)
connected to a lamp.
Local data load enable (Modman
MP10B) connected to a normally open
switch.
Discrete input
connections
Ground transmit enable (Modman
MP11D) connected to a normally open
switch.
Public service disable (Modman MP11E)
connected to a normally open switch.
Modman reset (Modman MP10C)
connected to a normally open switch.
Tx mute (KANDU J1D) connected to a
normally open switch.
External modem mode (Modman J1-B
11C) connected to a switch.
AV1 (Modman TP BB1 thru 4)
connected to a RJ45 Ethernet
connector.
Ethernet port
connections
Electrically wire and interconnect in
accordance with Figure 3-12.
Additional electrical
wiring
Examine for physical damage.PhysicalModman
Environmental conditions, refer to Figure
3-6 or Figure 3-7.
Install applicable 4-MCU tray, supplied
by customer.
Mounting tray
Page C-1
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal