Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
(5) L3 Codes
(a) The L3 code is four hexadecimal digits, used to uniquely identify the fault or event
against an L1, L2 code pair.
(b) Each LRU defines their own L3 codes. These are given in the fault table, refer to
Table 6-1.
Table 6-1. L1, L2 and L3 Codes
Repair actionLog type
L3L2L1
DescriptionCode
Descrip-
tion
Code
Descrip-
tion
Code
Status
Message
OAE Not
pointed
correctly
1Unknown0System0
look for the
contributing critical
fault entries
Critical Faults
critical fault
mode entry
0Mode1System0
Status
Message
dataload mode
entry
1Mode1System0
Status
Message
Commanded
mode entry
2Mode1System0
Status
Message
Normal mode
entry
3Mode1System0
configure tail number
on the GUI, ensure
APM is installed
Critical Faults
Tail number
Missing
0
Configura-
tion
3System0
Dataload APM
configuration files
Critical Faults
Configuration
File Missing
1
Configura-
tion
3System0
Datload the
incompatible LRU.
Note: could happen on
the power up after
dataload and that is
normal.
Critical Faults
Inter-LRU SW
Incompatibility
2
Configura-
tion
3System0
Normal for first boot upStatus
Message
Geographical
map missing
3
Configura-
tion
3System0
Dataload APM
configuration filesCritical Faults
Configuration
File in APM
missing
4
Configura-
tion
3System0
enter the proper
mission configurationsWarning
ACTIVE
MISSION FILE
MISSING
7
Configura-
tion
3System0
Page 6-13
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal