Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
Table 6-1. L1, L2 and L3 Codes (Cont)
Repair actionLog type
L3L2L1
DescriptionCode
Descrip-
tion
Code
Descrip-
tion
Code
Dataload the BUC-PA
software
Status
Message
LRU PRI-SEC
IMAGE
MISMATCH
6
Software
Configuration
FDBUC-PA2
If failed, dataload
BUC-PA again
Status
Message
DataLoad7
Software
Configuration
FDBUC-PA2
Status
Message
DataLoader
Connected
8
Software
Configuration
FDBUC-PA2
Status
Message
DataLoader
Disconnected
9
Software
Configuration
FDBUC-PA2
Status
Message
Operating
Image List
A
Software
Configuration
FDBUC-PA2
Dataload the
mismatched LRUStatus
Message
Secondary
Image
Corruption
Warning
B
Software
Configuration
FDBUC-PA2
Status
Message
OTA Staged
Software
DataLoad
C
Software
Configuration
FDBUC-PA2
If persist, check wiring
between KANDU-
BUC-PA Note: this can
happen as part of
power down
Status
Message
BUC-PA-
>KANDU
Heartbeat
failure
0
Software
Runtime
FEBUC-PA2
Status
Message
KANDU->BUC-
PA Heartbeat
failure
1
Software
Runtime
FEBUC-PA2
Status
Message
BUC-PA Main
Temperature
Sensor
1
Tempera-
ture
FFBUC-PA2
Reset the system, if
problem persist,
contact Honeywell
support
Status
Message
BUC-PA Main
Temperature
Sensor
1
Tempera-
ture
FFBUC-PA2
If power drop log is
also observed from
KANDU, check aircraft
power supply. If only
Shed load in FMA,
check cabling between
KANDU and FMA
Critical FaultsEnter Shed load1Unknown0FMA4
Page 6-26
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal