Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
Table D-1. Primary Labels (Cont)
Roll rate327
Yaw rate330
Ground Speed175
NOTE: Some labels have alternatives, only on of each is required (254 or
110, 255 or 111, 261 or 76 or 361, 132 or 314, 175 or 112 or 312).
These are listed as secondary and tertiary labels. When the primary
labels are populated, the secondary and tertiary labels are disabled.
(2) Ethernet Configuration
The Ethernet Configuration defines which ports are used for Traffic and which ports are
used for the Services (Data Load, GUI, SNMP).
Separate ports may be used for traffic and services, or a single port may be used for both.
Specify which ports are required, the default maintenance port is AV1.
The default local address is are (172.29.55. 1 / 2 / 3), for AV1.
NOTE: The AV1 is the default data loading port, any other Ethernet ports can be
selected as long as the APM configuration file is configured to allow that port
to data load.
(3) Weight on Wheels Polarity
Use the drop down selection in column B and C to indicate if WOW is wired and the polarity
when on ground.
(4) Ground Transmit Enable Polarity
Use the drop down selection in column B the polarity when of the ground transmit enable
discrete.
(5) Antenna Alignment Parameters
Figure D-6. Antenna Alignment Parameters
Note the antenna type is populated from the generic tab.
An option is provided for a lab simulation (the default is No)
(a) Select the radome manufacturer.
For FMA solutions the antenna alignment angles will automatically populated in
the table, for the specified aircraft in the generic tab.
Page D-9
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal