Users Manual Part 3
Table Of Contents
- 3. System Fails Post-Installation Checks
- 4. Incorrect Navigation Data
- 5. System Will Not Connect to the Network
- 6. Connectivity of Each Ethernet Port
- SECTION 7 – MAINTENANCE AND REPAIR
- 1. Maintenance Requirements
- 2. Continued Airworthiness, FAR 25.1529
- 3. Airworthiness Limitations
- 4. General Instructions for Inspection
- 5. Electrical and Mechanical Inspection and Check
- 6. Instructions for Continued Airworthiness
- 7. Visual Inspection and Check
- 8. Scheduled Maintenance and Inspections
- 9. Unscheduled Maintenance
- 10. Repair Requirements
- APPENDIX A – ENVIRONMENTAL CHARACTERISTICS
- APPENDIX B – INFORMATION SHEETS
- 1. Aircraft Information Sheet
- 2. JetWave™ MCS-8562 Terminal AES Subsystem Components
- A. JetWave™ MCS-8562 Terminal AES OAE - FMA Installation Information Sheet
- B. JetWave™ MCS-8562 Terminal AES KANDU Installation Information Sheet
- C. JetWave™ MCS-8562 Terminal AES BUC-HPA Installation Information Sheet
- D. JetWave™ MCS-8562 Terminal AES Modman Installation Information Sheet
- E. JetWave™ MCS-8562 Terminal AES APM Installation Information Sheet
- APPENDIX C – CHECKLISTS
- APPENDIX D – CUSTOMER PORTAL
- 1. Customer Portal
- 2. APM Request Form
- A. Requester Name
- B. Requester Email
- C. Honeywell Representative Name
- D. Hon Representative Email
- E. PO Number
- F. DP/VAR/Customer Name
- G. DP/VAR/Customer Name Contact Name
- H. DP/VAR/Customer Name Contact Email
- I. Channel Partner/Integrator/STC
- J. Estimated APM Due Date
- K. Aircraft Make / Aircraft Model
- L. Aircraft Model Variant
- M. Additional Notes/Comments
- 3. APM Parameter File
- 4. Request Assistance
If unknown or not applicable, please leave blank.
M. Additional Notes/Comments
Please enter any other pertinent information.
NOTE: If you require a modified APM File based on an existing APM File, enter "APM Based
on" VDD Number in the Additional Notes/Comments field.
3. APM Parameter File
A. Generic
The generic tab specifies the type of APM request:
A repeat APM File request (the customer will be able to obtain this from the customer portal)
by specifying the VDD number (VDD-9040xxxx-REV-xxx). No other information is required.
-
- An APM File based upon a specified APM File (VDD-9040xxxx-REV-xxx), with the parameter
changes detailed in the parameter file (detailed in the following section).
- A new APM File, (provide as much information as possible detailed in the following section).
Specifying the generic parameters (i.e. Aircraft Make, Model and Variant) provides information for
the other spreadsheet tabs.
NOTE: If the Aircraft Make, Model and Variant for the required aircraft are not listed in the
menus, select Other and specify the Aircraft Make, Model and Variant.
Figure D-5. Generic APM Parameters
B. APM Parameters
The requester / customer is required to provide as much information as possible. This will ensure
the APM File is delivered in a timely manner.
As a minimum, the following information is required:
Aircraft Make, Model and Variant-
- Individual Aircraft (Tail Number) or Fleet
- Antenna Type - Fuselage Mount Antenna (FMA)
- Inertial Reference System (IRS) reference.
- Multi Mode Receiver (MMR) or other equipment.
- A429 Labels available on the KANDU port.
Page D-7
23-15-84
EFFECTIVITY
ALL
11 Nov 2020
© Honeywell International Inc. Do not copy without express permission of Honeywell.
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
JetWave™ MCS-8562 Terminal