User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 2–17
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
3. Type 9 for Cooperative Rockwell-Collins SAT-906 and then press Enter.
A system message appears stating that the EEPROM has been updated.
(b) Configuring the Number of Channel Cards
HSD transceivers operating in Cooperative Mode must be configured as
single-channel units—even if the unit is a dual-channel transceiver.
To configure the transceiver as a Single Channel system:
1. In Menu 3, press M.
2. Type 10 to select the “Number of Channel Cards” parameter and then press
Enter.
3. Type 1 for the number of channel cards and then press Enter.
A system message appears stating that the EEPROM has been updated.
This completes the configuration of the system’s number of channel cards.
You now need to configure the LES Access Codes as described in
"Configuring LES Access Codes (All Modes)" on page 2-24.
(3) Configuring System Parameters for Honeywell Combined Mode
To operate the HSD transceiver in Honeywell Combined Mode, you need to configure
the following system parameters using the Honeywell SATCOM Direct
Commissioning and Maintenance Terminal (CMT) and the HSD Maintenance Port
Utility.
To configure the Honeywell System Parameters:
1. First, use the Honeywell CMT to:
• Obtain the HPA to antenna loss from the Honeywell SDU
• Configure High Rate Data Support settings (recommended—but not
mandatory)
2. Then use the HSD Maintenance Port Utility to:
• Configure the Terminal Category (only required when the recommended
hardware strapping is not used)
• Set Swift64 (M4) and Aero service priorities
• Change the LES Access Codes
• Reset the system to activate the new configuration.
TERMINAL CATEGORY HW STRAPPED VALUE
0=SAT906 1=STANDALONE 2=HW STRAPPING 3=MCS3000 4=MCS6000 5=MCS7000
6=MCS COMB 7=STANDALONE W/O ANTENNA 8=HCM COMBINED
9=COOPERATIVE ROCKWELL-COLLINS SAT906 10=OLD COMBINED MODE DEVELOP
11=HSD-X NETWORK 12=HSD-X NETWORK W/O ANTENNA 13=VIPER
NEW TERMINAL CATEGORY = ? 9