User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 2–14
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
C. Configuring System Parameters using the Maintenance Port Utility
This section describes how to configure the system parameters for all modes and
configurations of HSD operation, including: Stand-Alone Mode, Cooperative Mode,
Honeywell Combined Mode, Selective Mode, and Multi-Channel Configurations.
(1) Configuring System Parameters for Stand-Alone Mode
This section describes how to use the HSD Maintenance Port Utility to configure the
HSD system parameters for operation in Stand-Alone Mode.
Refer to "Test and Fault Isolation" on page 4-1 for detailed instructions on how to
connect to and use the HSD Maintenance Port Utility Program.
When all the required system parameters have been configured, “reset” or cycle the
power on the HSD to activate the new configuration.
To configure the required system parameters first establish a connection to the HSD
Maintenance Port Utility program:
• Connect a computer to the maintenance port of the HSD transceiver as described
in
"Test and Fault Isolation" on page 4-1, and then power up the system.
• Using a terminal emulation program, open the HSD maintenance utility program.
20 ISDN 84 5 800103 Mobile AMBE (4.8 kbps
LSV)
21 ISDN 85 6 800103 Mobile AMBE (4.8 kbps
LSV)
22 ISDN 86 7 800103 Mobile AMBE (4.8 kbps
LSV)
23 ISDN 87 8 800103 Mobile AMBE (4.8 kbps
LSV)
24 ISDN 88 9 800103 Mobile AMBE (4.8 kbps
LSV)
25 ISDN 89 A 800103 Mobile AMBE (4.8 kbps
LSV)
26 ISDN 90 B 800103 Mobile AMBE (4.8 kbps
LSV)
27 ISDN 91 C 800103 Mobile AMBE (4.8 kbps
LSV)
28 ISDN 92 D 800103 Mobile AMBE (4.8 kbps
LSV)
29 ISDN 93 E 800103 Mobile AMBE (4.8 kbps
LSV)
30 ISDN 94 F 800103 Mobile AMBE (4.8 kbps
LSV)
31 ISDN 95 10 800103 Mobile AMBE (4.8 kbps
LSV)
Table 2–5. System Assignments for Incoming Calls (Fixed-to-Mobile)
Entry PERIPH MSN TID Call Type REDIR