User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 1–15
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
HSD-128 dc input power
1110-A-0001, 1110-A-0160
Voltage Minimum: 22 V dc
Typical: 27.5 V dc
Maximum: 30.3 V dc
Power dissipation
(Stand-Alone)
Minimum: 275 W
Maximum: 370 W
Power dissipation
(Selective, Combined, and
Cooperative)
Minimum: 325 W
Maximum: 370 W
HSD-128 ac input power
1110-A-0060, 1110-A-0150
Voltage Minimum: 100 V rms
Typical: 115 V rms
Maximum: 122 V rms
Power dissipation
(Stand-Alone)
Minimum: 275 W
Maximum: 385 W
Power dissipation
(Selective, Combined, and
Cooperative)
Minimum: 325 W
Maximum: 385 W
Frequency Minimum: 360 Hz (Typical: 400 Hz)
Maximum: 440 Hz
HSD-64 dc input power
1110-A-0080
Voltage Minimum 22 V dc (Typical 27.5 V dc)
Maximum 30.3 V dc
Power dissipation Minimum: 275 W
Maximum: 370 W
HSD-64 ac input power
1110-A-0070
Voltage Minimum 100 V rms (Typical 115 V rms)
Maximum 122 V rms
Power dissipation
Frequency
Frequency band
Minimum: 275 W
Maximum: 385 W
Minimum: 360 Hz (Typical: 400 Hz)
Maximum: 440 Hz
Tx: 1626.5 to 1660.5 MHz
Rx: 1525.0 to 1559.0 MHz
Power requirements HSD
PN 1110-A-0001, 1110-A-0080,
1110-A-0160
+ 28 V dc nominal @ 13.5A
Table 1–13. HSD Equipment Characteristics and Specifications
CHARACTERISTIC SPECIFICATION