User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 1–8
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(e) Multi-Channel Configurations
In a Multi-Channel configuration, the minimum requirement for HSD-128 Control
Processor software is version 7.0. Version 7.0, Control Processor software is
available via HSD Service Bulletin 1110-SB-0012. HSD-X Transceiver
Extensions require Control Processor software version 6.0.
In Multi-Channel configurations, both the HSD-128 and the HSD-X units must
have the same Channel Card and Data I/O software versions installed. When
upgrading software in either the HSD-128 or HSD-X, verify that the software
version is compatible for operation in Multi-Channel systems as indicated in the
applicable service bulletin.
The minimum requirements and recommendations for software are shown in
Table 1–10.
(4) Software Version Description
This section provides a brief description of the deltas between versions of operational
software.
Table 1–11 provides a matrix of software versions, applicable service
bulletins, compliance requirements, and a brief description of the software deltas.
Table 1–9. Selective Mode Minimum Software Requirements
Unit
Part
Number
Software
PN
Software
Type
Minimum
Software
Req’t
Recommended
Software
HSD-128 1110-A-0001
1110-A-0060
1110-A-0150
1110-A-0160
1110-A-0048 Control
Processor
5.7 7.5 (or later)
1110-A-0082 Channel
Card
C35 C41 (or later)
Table 1–10. Multi-Channel Configuration Recommended Software Requirements
Unit
Part
Number
Software
PN
Software
Type
Minimum
Software
Req’t
Recommended
Software
HSD-128 1110-A-0001
1110-A-0060
1110-A-0150
1110-A-0160
1110-A-0048 Control
Processor
7.0 7.5 (or later)
1110-A-0082 Channel
Card
6.0 (C41) 6.0 (C41) (or
later)
HSD-X 1110-A-0401 1110-A-0420 Control
Processor
6.0 6.0 (or later)
1110-A-0082 Channel
Card
6.0 (C41) 6.0 (C41) (or
later)
1110-A-0240 Data I/O
Software
115 Superceded by
1110-A-0115
1110-A-0115 Data I/O
HSD-X
117 117