User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–52
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(5) Configuration Parameters Verification
The system configuration parameters can now be verified. Verify and document using
"Installation Checklist" on page D-1.
(a) Parameter Verification Procedure
For units operating control processor software versions 5.7 or earlier:
1. From Menu 3, select item ‘L’ (list EEPROM). The EEPROM listing appears
on the screen. The EEPROM listing appears as shown in Figure 4–30.
2. From Menu 4, select item ‘Q’ (channel card forward IDs). Ensure the
displayed Forward ID(s), for all channel cards, are correct.
For units operating control processor software versions 5.7 or later:
• From Menu 3, select item ‘O’ (list ORT). The ORT listing appears on the
screen, as shown in
Figure 4–31. Verify that the correct system configuration
parameters are listed in the ORT.
5.0 Remotes
(Optional—but
recommended)
Remote Reset switch operation
Maintenance Port, remote access
Power and Fault LED indicators
6.0 RF Coax Rx input cable loss from DLNA to HSD at BP12 and to the
RFU at TPC1 (including splitter)
Tx output cable loss from HSD at MPC1 to DLNA
7.0 Antenna
Connection
Antenna manufacturer and model
Multi-Control loopbacks installed from TP3E to TP1A and
TP3F to TP1B (Stand-Alone Mode)
8.0 SDU HSD to SDU interconnect wiring confirmed
(Non-Stand-Alone modes)
Table 4–24. HSD Electrical Verification
STEP Item Checked Verification Description