User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–51
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Table 4–23. HSD Electrical Verification
STEP
Item
Checked
Verification Description
1.0 Power
connections
Model 1110-A-0001/1110-A-0080/1110-A-0160:
28 V dc polarity
Model 1110-A-0060/1110-A-0070/1110-A-0150:
115 V ac polarity
Chassis Ground @ BP8 – resistance measurement
2.0 Voltage
levels
CAUTION: When power is applied to the rack, the fan
energizes.
Check voltage levels:
Model 1110-A-0001/1110-A-0080/1110-A-0160 (28 V dc):
between BP2 (
+
ve) and BP3 (return)
Model 1110-A-0060/1110-A-0070/1110-A-0150 (115 V ac):
between BPI (115-H) and BP7 (115-C)
3.0 IRS Input IRS wiring:
Inertial system wired to TP4J (A) and TP4K (B)
IRS format:
ARINC 429 Interface
Table 4–24. HSD Electrical Verification
STEP Item Checked Verification Description
1.0 Configuration
Strap Pins
SDI: Strapped for HGA, Pin TP5B to TP5D
System Configuration:
Strapped for System Mode, Pins TP4A, TP4B, TP4C, and/or
TP4D strapped to TP7K
Data I/O:
User specific, default to unrestricted (ISDN only): Pins
MP5H to TP7K
Forward Address: User specific
WOW: (Optional)
2.0 Ethernet Strapped to RJ45 distribution points
Note: Optional—other service may be preferred.
3.0 ISDN Strapped to RJ45 distribution points
Note: Optional—other service may be preferred.
4.0 DTE - MPDS
(RS232)
Strapped to DB9S distribution connector
Note: Optional—other service may be preferred.