User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–29
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(h) Menu 15
Menu 15 was added in control processor software version 7.0 to allow the user
to query the system for channel-card, software versions and serial number
information.
Figure 4–24 shows the HSD maintenance utility program Menu 15 screen
display. Table 4–16 describes the items available in Menu 15.
Figure 4–24. Menu 15 Screen Display
(i) Menu 18
Menu 18 was added in control processor software version 7.0 to support
Multi-Channel configurations. No additional menu items were added with the
release of Version 7.5, Control Processor software. Menu 18 is only available if
the HSD system is configured to either HSD-X Network, HSD-X without Antenna,
or Viper terminal categories.
Figure 4–25 shows the HSD maintenance utility program Menu 18 screen
display. Table 4–17 describes the items available in Menu 18.
Figure 4–25. Menu 18 Screen Display
MENU 15 FIRMWARE V7.0
V request channel card versions D channel card serial number
<CTRL> N next menu <CTRL> O previous menu = select reports
Table 4–16. Menu 15 Item Descriptions
Menu Item Item Description
V: request channel card
versions
• Displays software versions for a selected channel
card
D: channel card serial
number
• Displays the serial number of the selected channel
card
MENU 18 FIRMWARE V7.0
X HSD-X slave console mode B HSD-X slave cable loss
L list HSD-X slave cable loss V get HSD-X firmware version
<CTRL> N next menu <CTRL> O previous menu = select reports