User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–26
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(e) Menu 10
Menu 10 items are used to manually enter INS parameters to simulate the INS
data required for HSD operation when INS data is unavailable.
Figure 4–21
shows the HSD maintenance utility program Menu 10 screen display. Table 4–
13 describes the items available in Menu 10. No additional menu items were
added with the release of Version 7.5, Control Processor software.
In control-processor software version 7.0, the following changes were made to
Menu 10 selections (delta between version 4.5 and 7.0).
• Added item C, ‘simul port ACU status’, which prompts the user to enter both
the port antenna gain in dB and the message rate in Hz.
• Added item M, ‘activate antenna status words’, which activates all set
antenna status words.
• Added item N, ‘deactivate antenna status words’, which deactivates all set
antenna status words.
• Added item B, ‘simul sb ACU status’, which prompts the user to enter the
Starboard antenna gain in dB and the message rate in Hz.
Figure 4–21. Menu 10 Screen Display
MENU10 FIRMWARE Vx.x
L simul INS lat G simul INS long
H simul INS heading T simul INS true track
P simul INS pitch R simul INS roll
S simul INS speed A activate all simul words
X deactivate all simul words C simul port ACU status
B simul sb ACU status M activate antenna status words
N deactivate antenna status words
<CTRL> N next menu <CTRL> O previous menu = select reports
Table 4–13. Menu 10 Item Descriptions
Menu Item Item Description
L: simul INS lat
• Allows user to simulate a latitude by overriding the data
received from the aircraft INS
H: simul INS heading
• Allows user to simulate a aircraft heading by overriding
the data received from the aircraft INS
P: simul INS pitch
• Allows user to simulate aircraft pitch by overriding the
data received from the aircraft INS
S: simul INS speed
• Allows user to simulate aircraft speed by overriding the
data received from the aircraft INS
X: deactivate all simul
words
• De-activates all simulated parameters reverting the HSD
system back to using the INS data received from the
aircraft