User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–20
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Table 4–10. Menu 3, Item 'M' EEPROM Parameter Descriptions (Version 4.5)
Parameter
#
Parameter Title Description
1 HPA Cable loss • Measured transmit coax cable loss from the HSD
at MPC1 to the antenna including the DLNA loss
(0.8 dB)
• Maximum is 2.5 dB – 0.8 dB = 1.7 dB
2 Forward ID • Entry required ONLY if the ID is not strapped,
refer to "Installation" on page 3-1 for strapping
details
3, 21, 22,
and 23
AORW, AORE, POR,
and IOR ‘LES’
Access Codes
• Inmarsat Service Provider LES access code
entry; default is “1”
4 Terrestrial Network ID • Used to change Terrestrial Network ID (where
applicable)
10 Number of Channel
Cards
• Entry selects the number of channel cards the
system is configured for.
• Default for Stand-Alone Mode installations is “2”
11 Front Panel LEDs
Enabled
• Future consideration is provided for additional
LEDs, beyond the two currently activated
• Default is “2”’
14 Maintenance Port
Inverse Video
• Enables a selected “reports” item to be
highlighted in Inverse Video when it is activated
• Default is “1” (activated)
15 Maintenance Port
Degrees Symbol
• Offers a choice of displaying the letter “D” or the
degree symbol “
°” when viewing the lat/long
information displayed in the ‘Reports’ output:
• Select “0” to use the letter “D”, e.g. 180.0 D
• Select “1” to use a degree symbol “
°”, e.g.
180.0
°