User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–12
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Figure 4–12. Level 2, Menu 15
Figure 4–13. Level 2, Menu 18
Note: In control processor software, version 7.0, Menu 18 is available when the
terminal category is set to HSD-X Network, HSD-X Antenna, or Viper
configurations.
(6) Menu Item Descriptions
This section provides a brief description of the Level 2, maintenance-utility-program
menu items used for test and fault isolation procedures.
Although this section only provides illustrations and descriptions for Level 2 access,
descriptions of all Level 1 access menu items shown in
Figure 4–5 are covered. (All
Level 1 menus are included in Level 2 Menus.)
In active HSD systems, menu screens display the firmware version.
Note: Depending on the version of software installed, the number of channels
cards in the system, and the HSD configuration mode, the menu and report
items available to users may differ slightly from the illustrations shown and
described in this document.
(a) Menu 1
Figure 4–14 shows the HSD maintenance utility program Menu 1 screen display.
Table 4–7 describes the items available in Menu 1.
In control processor software, version 7.0, the following changes were made to
menu 3 selections (delta between version 4.5 and 7.0). No additional menu items
were added with the release of Version 7.5, Control Processor software.
• Added menu items, S ‘set hcm attenuator’ and R ‘ hcm RF threshold’
MENU 15 FIRMWARE V7.0
V request channel card versions D channel card serial number
<CTRL> N next menu <CTRL> O previous menu = select reports
MENU 18 FIRMWARE V7.0
X HSD-X slave console mode B HSD-X slave cable loss
L list HSD-X slave cable loss V get HSD-X firmware version
<CTRL> N next menu <CTRL> O previous menu = select reports