User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 4–8
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
(a) End User Access: Level 1 – Password: MENU
This limited-access level is for anyone without technical training on the product.
It provides read-only access to help users diagnose problems with the assistance
of product support personnel.
(b) Field Representative Access: Level 2 – Password: MAINT
This level is for trained original equipment manufacturer (O.E.M.) installers and
product support personnel. This access level supports “read’” and limited “write”
capabilities. Users are able to disable/mask/clear faults, change satellite or LES
preferences, view and modify certain EEPROM parameters, and perform other
maintenance or upgrade functions.
(4) Using the HSD Maintenance Utility Program
This section describes the basic operating instructions for using and navigating the
HSD maintenance utility program.
(a) Entering Passwords
• For untrained users use Level 1 access: Type menu, and then press Enter.
• For trained technicians and product support personnel use Level 2 access:
Type
maint, and then press Enter.
Note: The typed password does not appear on the screen.
(b) Navigating the HSD Maintenance Utility Program
• To scroll through the available menus press Ctrl+N.
• To go to the previous menu, press Ctrl+O.
• To refresh the menu screen or exit from a Reports Menu press ESC.
(c) Selecting MENU Items
• To enable test or data entry functions, press the letter associated with the
menu items. When a menu item is selected, the application may prompt the
user for additional inputs or selections.
(d) Selecting Report Items
• To open the list of possible system reports, press the equals sign (=).
A list of report items appears. Active reports show as toggled “ON.” Inactive
reports show as toggled “
OFF.”
• To activate a report item, type the report item number and then
press Enter.
Note: Multiple report items can be activated at the same time; however, you must
type and enter each report item number separately.
•To turn “OFF” individual, active report items, type the report item number you
want to toggle off, and then press
Enter.
•To turn “OFF” all active report items, press the equals sign (=) to display the
report item list, and then press
X.