User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–26
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
1.
BSU Pin nomenclature for Mechanically-Steered Antennae (MA) is manufacturer dependent.
2. “Other antenna types” (OA) represent either conformal or phased array antennae.
Table 3–11. Stand-Alone Mode ARINC 600 Middle Plug Connection Details
I/O
From
Middle
Plug
Signal Name To Description
O
1A LED 1 Remote Status Panel—
Green
HSD—Power On
(Optional)
O
1B LED 2 Remote Status Panel—
Red
HSD—Fault (Optional)
O
1F LED Common Remote Status LED
Panel, and closed side of
N.O. Remote Reset
Switch
LED Common
O
1G Maint Port Tx
(OUT)
Maint Port serial data,
DB9S-2
Maintenance computer
(laptop/PC), for “Remote”
access
I
1H Maint Port Rx (IN) Maint Port serial data,
DB9S-3
I/
O
1J Maint Port Signal
Ground.
Maint Port serial data,
DB9S-5
O
2A CC (channel
card) #1 Rx
DTE-1A, DB9S-2 or
DB25P-3
User Mobile Packet Data
(MPDS), RS-232, DTE-1A
I
2B CC #1 Tx DTE-1A, DB9S-3 or
DB25P-2
I
2C CC #1 RTS DTE-1A, DB9S-7 or
DB25P-4
O
2D CC #1 CTS DTE-1A, DB9S-8 or
DB25P-5
I
2E CC #1 DTR DTE-1A, DB9S-4 or
DB25P-20
O
2F CC #1 DSR DTE-1A, DB9S-6 or
DB25P-6
O
2G CC #1 CD DTE-1A, DB9S-1 or
DB25P-8
O
2H CC #1 RI DTE-1A, DB9S-9 or
DB25P-22
I/
O
2J CC #1 SGND DTE-1A, DB9S-5 or
DB25P-7