User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
Page 3–25
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
I
5F FWD Address, BIT
24 (LSB)
1=no connection, Six digit Hex ID assigned
by Inmarsat /EMS
I
5G FWD Address, BIT
I
5H FWD Address, BIT
I
5J FWD Address, BIT
I
5K FWD Address, BIT
20
I
6A FWD Address, BIT
I
6B FWD Address, BIT
I
6C FWD Address, BIT
I
6D FWD Address, BIT
I
6E FWD Address, BIT
I
6F FWD Address, BIT
I
6G FWD Address, BIT
I
6H FWD Address, BIT
I
6J FWD Address, BIT
I
6K FWD Address, BIT
I
7A FWD Address, BIT
I
7B FWD Address, BIT
I
7C FWD Address, BIT
I
7D FWD Address, BIT
I
7E FWD Address, BIT
I
7F FWD Address, BIT
I
7G FWD Address, BIT
I
7H FWD Address, BIT
I
7J FWD Address, BIT
1 (MSB)
I
7K FWD Address,
Common
Common GND
connection for system
and I/O configuration and
Table 3–10. Stand-Alone Mode ARINC 600 Top Plug Connection Details
I/O
From
Top Plug
Signal Name To Description