User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Page TC–5
18 September 2007
(1) General Overview.......................................................................................... 4-3
(2) Connection Requirements ............................................................................. 4-4
(3) Accessing the Maintenance Utility Program .................................................. 4-7
(4) Using the HSD Maintenance Utility Program................................................. 4-8
(5) Menu Descriptions......................................................................................... 4-9
(6) Menu Item Descriptions............................................................................... 4-12
(7) Report Item Descriptions ............................................................................. 4-30
(8) Activating Maintenance Reports.................................................................. 4-33
D. Fault Definitions ............................................................................................... 4-36
(1) Cause Indication (Fault Codes) ................................................................... 4-36
(2) Inmarsat Cause Codes................................................................................ 4-36
E. Operational and Diagnostic Test Procedures ................................................... 4-48
(1) General........................................................................................................ 4-48
(2) Test Setup Procedure .................................................................................. 4-49
(3) Post Test...................................................................................................... 4-50
(4) Installation and Operational Verification Tests............................................. 4-50
(5) Configuration Parameters Verification ......................................................... 4-52
(6) System Power-up Checks ........................................................................... 4-55
(7) System On-Air Checks ................................................................................ 4-56
(8) Antenna Tracking Checks............................................................................ 4-60
(9) Optional System Checks ............................................................................. 4-61
F. Operational Mode and Configuration System Checks ...................................... 4-62
(1) Verifying Cooperative Mode System Operation........................................... 4-62
(2) Verifying Honeywell Combined Mode System Operation ............................ 4-62
(3) Verifying Multi-Channel Configuration System Operation ........................... 4-67
G. Software Load Procedures............................................................................... 4-70
(1) Loading Channel Card Software ................................................................. 4-71
(2) Loading Control Processor Software........................................................... 4-73
(3) Forcing Channel Card Power Up Procedure ............................................... 4-76
(4) Loading HPA Software................................................................................. 4-76
(5) Verifying Software Loads............................................................................. 4-78
(6) Disconnecting Load Equipment................................................................... 4-79
(7) Completing Record of Accomplishment ...................................................... 4-80
3. Troubleshooting and Fault Isolation....................................................... 4-81
A. Troubleshooting Principles ............................................................................... 4-81
(1) Non-specific Complaints.............................................................................. 4-81
(2) Specific Complaints ..................................................................................... 4-81
B. Equipment Required......................................................................................... 4-81