User's Manual
Table Of Contents
- Introduction
- System Description
- 1. Purpose of Equipment
- 2. Equipment Covered
- 3. Equipment Description
- A. Applicable Documents
- B. Reference Documents
- C. Equipment Specifications
- D. Mechanical Description
- E. Electrical Description
- F. System Interface Descriptions
- G. User Interfaces
- (1) Stand-Alone Mode User Interfaces
- (2) Collins Cooperative Mode User Interfaces
- (3) Honeywell Combined Mode User Interfaces
- (4) Selective Mode User Interfaces
- (5) Multi-Channel Configurations
- (6) ISDN Circuit-Switched Data Interface
- (7) RS-232 Interface
- (8) Ethernet Data Interface
- (9) ISDN S/T Interface
- (10) Maintenance Port Interface
- H. Initiated-Self-Test
- I. Owner Requirements Table
- 4. Inmarsat System Overview
- 5. HSD Modes and Configuration Descriptions
- System Operation
- 1. Introduction
- 2. Activating HSD Transceivers
- 3. Configuring HSD Systems
- 4. Using the HSD System
- Installation
- 1. Introduction
- 2. Advisories
- 3. Pre-Installation Inspection
- 4. Unpacking and Inspecting Equipment
- 5. Cabling and Connector Requirements
- 6. ARINC 600 Trays and Connectors
- 7. Mechanical Installation
- 8. Electrical Installation
- 9. Outline/Installation and Interconnection/Contact Assignment Diagrams
- Test and Fault Isolation
- 1. Introduction
- 2. Operational and Diagnostic Testing
- 3. Troubleshooting and Fault Isolation
- 4. Adjustment/Alignment Procedures
- 5. Modification History
- Maintenance and Repair
- 1. General
- 2. Maintenance
- 3. Repair
- 4. Instructions for Continued Airworthiness, FAR 25.1529
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- Appendix C: RJ-45 Cable Termination Details
- Appendix D: Installation Checklist
- Appendix E: Record of Accomplishment
- Appendix F: RF Splitter
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
Page TC–3
18 September 2007
(1) Overview........................................................................................................ 2-7
C. Configuring System Parameters using the Maintenance Port Utility................ 2-14
(1) Configuring System Parameters for Stand-Alone Mode ............................. 2-14
(2) Configuring System Parameters for Cooperative Mode ............................. 2-16
(3) Configuring System Parameters for Honeywell Combined Mode .............. 2-17
(4) Configuring System Parameters for Selective Mode .................................. 2-21
(5) Configuring System Parameters for Multi-Channel Configurations ............. 2-23
D. Configuring LES Access Codes (All Modes).................................................... 2-24
(1) General Overview ....................................................................................... 2-24
E. Removing the LED Label ................................................................................. 2-30
F. Activating Configurations .................................................................................. 2-30
(1) Verifying Configurations............................................................................... 2-31
G. Configuring System Parameters using the HSD Owner Requirement Tool...... 2-31
(1) Creating an ORT using the HSD ORT Tool ................................................. 2-32
(2) Saving the ORT file ..................................................................................... 2-38
(3) Loading the ORT ......................................................................................... 2-38
(4) Loading ORT Files....................................................................................... 2-39
4. Using the HSD System............................................................................. 2-43
A. Placing Voice and Fax Calls............................................................................. 2-43
(1) Dial Code Prefixes....................................................................................... 2-44
(2) Mobile-to-Mobile Communication ................................................................ 2-45
B. Using Data Connections................................................................................... 2-46
(1) Mobile ISDN versus MPDS ......................................................................... 2-46
(2) Connecting to Inmarsat Mobile ISDN Service ............................................. 2-46
(3) Connecting to Inmarsat MPDS ................................................................... 2-48
(4) Bonding Channel Cards in Two-Channel Card Systems............................. 2-50
INSTALLATION
1. Introduction................................................................................................ 3-1
2. Advisories ................................................................................................... 3-2
3. Pre-Installation Inspection......................................................................... 3-3
4. Unpacking and Inspecting Equipment ..................................................... 3-4
5. Cabling and Connector Requirements ..................................................... 3-5
A. Power Requirements.......................................................................................... 3-5
B. Ground Requirements ........................................................................................ 3-5