User's Manual
Table Of Contents
- Customer Response Form
- Record of Revisions
- Service Bulletin List
- List of Effective Pages
- Introduction
- System Description
- 1. Inmarsat System Overview
- 2. Equipment Overview
- 3. Equipment Specifications
- 4. System Interfaces
- 5. User Interfaces
- 6. Software Description
- System Operation
- 1. Registering and Activating Terminals
- 2. Configuring Terminals
- A. Setting up Airborne Networks
- B. Mapping User Devices for ISDN Services
- C. IMNs
- D. MSNs
- E. Configuring User ORT Parameters with the Maintenance Port Utility (MPU)
- F. Configuring Secure ORT Parameters with the Maintenance Port Utility (MPU)
- G. Creating ORTs with the Maintenance Port Utility (MPU)
- H. Understanding CMU Messages
- I. Configuring Swift 64 LES Access Codes
- J. Removing the LED Label
- K. Activating Configurations
- L. Verifying Configurations
- 3. Using Terminals
- Installation
- 1. Advisories
- 2. Pre-Installation Inspection
- 3. Mechanical Installation
- 4. Electrical Installation
- A. Cabling and Connector Requirements
- B. Installation Wiring Notes
- (1) Source/Destination Identification
- (2) Maintenance Port Interface
- (3) Antenna Subsystem RF Interface
- (4) WOW Pins
- (5) ICAO IDs
- (6) Remote Status Panel (Optional)
- (7) System Configuration Strapping
- (8) System Mode Strap Pins Coding
- (9) Call Light Activation Strapping
- (10) Hookswitch Strapping
- (11) Priority 4 Call Strapping
- (12) Cockpit Voice Strapping
- (13) User Interfaces
- (14) System Interfaces
- C. Connection Details
- 5. Passive Intermodulation (PIM) Test
- 6. Installation and Engineering Diagrams
- 7. Connection Details
- Test and Fault Isolation
- Maintenance and Repair
- Configuring the Owners Requirements Table (ORT)
- 1. Configuring ORT Parameters Using the MPU
- A. Connecting to the MPU
- B. Configuring the ORT Part Number
- C. Configuring Cockpit Communication Parameters
- D. Configuring 4-wire Parameters
- E. Configuring POTS Parameters
- F. Configuring CEPT-E1 Parameters
- G. Configuring High Speed Data Services
- H. Configuring Ethernet Parameters
- I. Configuring Networking Parameters For Ethernet 1 and Ethernet 2
- (1) Configuring the Host Name
- (2) Configuring the Access Concentrator Name
- (3) Configuring the SNMP Server
- (4) Configuring the SNMP Community String
- (5) Configuring the TFTP Server
- (6) Configuring the DHCP Client
- (7) Configuring the DHCP Server
- (8) Configuring Telnet Access
- (9) Configuring the Managed Range
- (10) Configuring the Number of Managed Addresses
- (11) Configuring the Access Point Name
- J. Configuring Avionics Parameters
- K. Configuring Satellite Service ORT Parameters
- (1) Configuring the Forward ID
- (2) Configuring Satellite Information
- (3) Configuring GES Service Provider Information
- (4) Configuring the Frequency Table
- (5) Configuring LES Service Provider Information
- (6) Configuring the SwiftBroadband Timing Mode
- (7) Configuring the Priority Service for Channel Card One
- (8) Configuring the Service Type Priority
- L. Configuring Antenna ORT Parameters
- M. Configuring MCDU ORT Parameters
- (1) Configuring MCDU Wiring
- (2) Configuring the MCDU Input Speed
- (3) Configuring the MCDU Output Speed
- (4) Configuring the MCDU Controller Type
- (5) Configuring the MCDU Type
- (6) Configuring the MCDU Font Colour
- (7) Configuring Manual Dialing
- (8) Configuring Outgoing Call Pre-Selection
- (9) Configuring the Address Book Categories
- N. Configuring the CMU
- O. Configuring Terminal Operation
- (1) Configuring Air/Ground Status Restrictions
- (2) Configuring Transmit on Ground
- (3) Configuring Self-test in Air
- (4) Configuring Maintenance Command Execution in Air
- (5) Configuring MCDU PAST
- (6) Configuring Field Loadable Software
- (7) Configuring the Logon/Handover Policy
- (8) Configuring Logon Interrogation
- (9) Configuring High-rate R/T in Global Beam
- (10) Masking Position in Logs
- (11) Configuring HSD SAL
- P. Configuring Passive Intermodulation (PIM) Parameters
- (1) Configuring PIMBIT HGA Azimuth Offset Angle
- (2) Configuring PIMBIT IGA Azimuth Offset Angle
- (3) Configuring PIMBIT IGA Elevation Offset Angle1
- (4) Configuring PIMBIT IGA Elevation Offset Angle2
- (5) Configuring PIMBIT HGA Elevation Offset Angle1
- (6) Configuring PIMBIT HGA Elevation Offset Angle2
- (7) Configuring PIMBIT Measurement Discard Ratio
- (8) Configuring PIMBIT Failure Threshold
- (9) Configuring PIMBIT Pointing Failure Threshold
- 2. Configuring ORT Parameters Using the EMS ORT Application
- 1. Configuring ORT Parameters Using the MPU
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- 1. Have you registered with a service provider to activate service?
- 2. Has your account been activated?
- 3. Is the HSD-440 Mark 2 Terminal seated properly?
- 4. Is all cabling attached correctly and securely?
- 5. Have any changes to the system been made?
- 6. Are your Primary and Secondary LES/GES Access Codes programmed for all ORs?
- 7. Was the operational mode of the system strapped or configured correctly?
- 8. Are the SIM cards activated?
- 9. Is the APN set?
- 10. Are GES preferences correctly set?
- Appendix C: RJ45 Cable Termination Details
- Appendix D: Installation Planning Checklist
- Appendix E: Installation Checklist
- Appendix F: CMU Messages
- Appendix G: International Access and Country Codes
- Appendix H: Inmarsat Cause Codes
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion® HSD-440 Mark 2 Terminal
23-15-30 H-14
3 JUN 10
B201 RF error RX VHF
B202 RF error RX Lband
B204 RF error RX VHF
B208 RF error TX Lband
B210 RF error RF error
B220 RF error Ref error
B27F Mod watchdog tripped
B280 Generic voice codec errors
B281 TMS spurious interrupt
B300 Outdoor terminal failure, check connections to ODU
B301 ODU error cannot set cable attenuator
B310 ODU error power response missing
B311 ODU error tune response missing
B312 ODU error HPA control response missing
B313 ODU error HPA status response missing
B314 ODU error alarm response missing
B315 ODU error burst timer response missing
B316 ODU error HPA backoff response missing
B320 ODU error alarm heat
B321 ODU error alarm burst
B322 ODU error alarm power
B323 ODU error alarm over voltage
B324 ODU error alarm reverse power
B328 ODU failed due to tx power check
B329 ODU error alarm timeout
B330 ODU error alarm timeout no trip
B400 Internal temperature of terminal too high, turn off for 10 minutes
B401 Internal temperature sensor failed
B410 Mod error, handshake failure, power down/up and try again
Table H-1 Inmarsat Cause Code Definitions (Continued)
Inmarsat Cause Code Code Definition