User's Manual
Table Of Contents
- Customer Response Form
- Record of Revisions
- Service Bulletin List
- List of Effective Pages
- Introduction
- System Description
- 1. Inmarsat System Overview
- 2. Equipment Overview
- 3. Equipment Specifications
- 4. System Interfaces
- 5. User Interfaces
- 6. Software Description
- System Operation
- 1. Registering and Activating Terminals
- 2. Configuring Terminals
- A. Setting up Airborne Networks
- B. Mapping User Devices for ISDN Services
- C. IMNs
- D. MSNs
- E. Configuring User ORT Parameters with the Maintenance Port Utility (MPU)
- F. Configuring Secure ORT Parameters with the Maintenance Port Utility (MPU)
- G. Creating ORTs with the Maintenance Port Utility (MPU)
- H. Understanding CMU Messages
- I. Configuring Swift 64 LES Access Codes
- J. Removing the LED Label
- K. Activating Configurations
- L. Verifying Configurations
- 3. Using Terminals
- Installation
- 1. Advisories
- 2. Pre-Installation Inspection
- 3. Mechanical Installation
- 4. Electrical Installation
- A. Cabling and Connector Requirements
- B. Installation Wiring Notes
- (1) Source/Destination Identification
- (2) Maintenance Port Interface
- (3) Antenna Subsystem RF Interface
- (4) WOW Pins
- (5) ICAO IDs
- (6) Remote Status Panel (Optional)
- (7) System Configuration Strapping
- (8) System Mode Strap Pins Coding
- (9) Call Light Activation Strapping
- (10) Hookswitch Strapping
- (11) Priority 4 Call Strapping
- (12) Cockpit Voice Strapping
- (13) User Interfaces
- (14) System Interfaces
- C. Connection Details
- 5. Passive Intermodulation (PIM) Test
- 6. Installation and Engineering Diagrams
- 7. Connection Details
- Test and Fault Isolation
- Maintenance and Repair
- Configuring the Owners Requirements Table (ORT)
- 1. Configuring ORT Parameters Using the MPU
- A. Connecting to the MPU
- B. Configuring the ORT Part Number
- C. Configuring Cockpit Communication Parameters
- D. Configuring 4-wire Parameters
- E. Configuring POTS Parameters
- F. Configuring CEPT-E1 Parameters
- G. Configuring High Speed Data Services
- H. Configuring Ethernet Parameters
- I. Configuring Networking Parameters For Ethernet 1 and Ethernet 2
- (1) Configuring the Host Name
- (2) Configuring the Access Concentrator Name
- (3) Configuring the SNMP Server
- (4) Configuring the SNMP Community String
- (5) Configuring the TFTP Server
- (6) Configuring the DHCP Client
- (7) Configuring the DHCP Server
- (8) Configuring Telnet Access
- (9) Configuring the Managed Range
- (10) Configuring the Number of Managed Addresses
- (11) Configuring the Access Point Name
- J. Configuring Avionics Parameters
- K. Configuring Satellite Service ORT Parameters
- (1) Configuring the Forward ID
- (2) Configuring Satellite Information
- (3) Configuring GES Service Provider Information
- (4) Configuring the Frequency Table
- (5) Configuring LES Service Provider Information
- (6) Configuring the SwiftBroadband Timing Mode
- (7) Configuring the Priority Service for Channel Card One
- (8) Configuring the Service Type Priority
- L. Configuring Antenna ORT Parameters
- M. Configuring MCDU ORT Parameters
- (1) Configuring MCDU Wiring
- (2) Configuring the MCDU Input Speed
- (3) Configuring the MCDU Output Speed
- (4) Configuring the MCDU Controller Type
- (5) Configuring the MCDU Type
- (6) Configuring the MCDU Font Colour
- (7) Configuring Manual Dialing
- (8) Configuring Outgoing Call Pre-Selection
- (9) Configuring the Address Book Categories
- N. Configuring the CMU
- O. Configuring Terminal Operation
- (1) Configuring Air/Ground Status Restrictions
- (2) Configuring Transmit on Ground
- (3) Configuring Self-test in Air
- (4) Configuring Maintenance Command Execution in Air
- (5) Configuring MCDU PAST
- (6) Configuring Field Loadable Software
- (7) Configuring the Logon/Handover Policy
- (8) Configuring Logon Interrogation
- (9) Configuring High-rate R/T in Global Beam
- (10) Masking Position in Logs
- (11) Configuring HSD SAL
- P. Configuring Passive Intermodulation (PIM) Parameters
- (1) Configuring PIMBIT HGA Azimuth Offset Angle
- (2) Configuring PIMBIT IGA Azimuth Offset Angle
- (3) Configuring PIMBIT IGA Elevation Offset Angle1
- (4) Configuring PIMBIT IGA Elevation Offset Angle2
- (5) Configuring PIMBIT HGA Elevation Offset Angle1
- (6) Configuring PIMBIT HGA Elevation Offset Angle2
- (7) Configuring PIMBIT Measurement Discard Ratio
- (8) Configuring PIMBIT Failure Threshold
- (9) Configuring PIMBIT Pointing Failure Threshold
- 2. Configuring ORT Parameters Using the EMS ORT Application
- 1. Configuring ORT Parameters Using the MPU
- Appendix A: Inmarsat Satellite Beam Coverage
- Appendix B: Troubleshooting Checklist
- 1. Have you registered with a service provider to activate service?
- 2. Has your account been activated?
- 3. Is the HSD-440 Mark 2 Terminal seated properly?
- 4. Is all cabling attached correctly and securely?
- 5. Have any changes to the system been made?
- 6. Are your Primary and Secondary LES/GES Access Codes programmed for all ORs?
- 7. Was the operational mode of the system strapped or configured correctly?
- 8. Are the SIM cards activated?
- 9. Is the APN set?
- 10. Are GES preferences correctly set?
- Appendix C: RJ45 Cable Termination Details
- Appendix D: Installation Planning Checklist
- Appendix E: Installation Checklist
- Appendix F: CMU Messages
- Appendix G: International Access and Country Codes
- Appendix H: Inmarsat Cause Codes
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion® HSD-440 Mark 2 Terminal
23-15-30 4-66
3 JUN 10
MCDU FONT COLOUR: ENABLED NOT DEFAULT SET BY MAINT PORT
COCKPIT OUTGOING CALL SIGNALING: DISABLED SET BY MAINT PORT
COCKPIT OUTGOING CALL PRE-SELECT: ENABLED SET BY MAINT PORT
PIMBIT AZIMUTH OFFSET ANGLES: SET BY MAINT PORT
HGA = 11.0 DEG NOT DEFAULT
IGA = 15.0 DEG NOT DEFAULT
PIMBIT IGA ELEVATION ANGLES: SET BY MAINT PORT
ANGLE 1 = 18.0 DEG NOT DEFAULT
ANGLE 2 = 12.5 DEG NOT DEFAULT
PIMBIT HGA ELEVATION ANGLES: SET BY MAINT PORT
ANGLE 1 = 27.6 DEG NOT DEFAULT
ANGLE 2 = 12.5 DEG NOT DEFAULT
HIT 'H' for MORE
PIMBIT TEST CRITERIA: SET BY MAINT PORT
MEASUREMENT DISCARD RATIO = 25.5% NOT DEFAULT
FAILURE THRESHOLD = 25.5 dB NOT DEFAULT
POINTING FAILURE THRESHOLD = 255 NOT DEFAULT
HIT 'H' for MORE
DIO BLOCK: 86 BYTES -- TYPE 1 CRC D3CD
de 8e 6a 67 00 50 de 96 e9 74 00 39 1c b6 5b b5 ..jg.P...t.9..[.
0c 8f 09 6e 1c d2 5b 2e de 92 88 f0 00 09 0c 96 ...n..[.........
e8 62 87 a2 fc f4 79 de ce eb 70 00 0e ac d3 2c .b....y...p....,
29 c0 a8 00 05 9b d3 2c 30 00 a1 de 82 6d 30 00 )......,0....m0.
04 1c d2 69 6e de c3 0b e5 00 0b c7 86 3b ad 06 ...in........;..
44 61 74 61 49 4f DataIO
ETHERNET 1 ADDRESS 192.168.0.1
ETHERNET 1 MASK 255.255.255.0
ETHERNET 2 ADDRESS 0.0.0.0
ETHERNET 2 MASK 255.255.255.0
DHCP CLIENT DISABLED
HOST NAME DataIO
DHCP SERVER DISABLED
START OF MANAGED RANGE 192.168.0.100
SNMP SERVER ENABLED
SNMP COMMUNITY STRING public
NUMBER OF MANAGED ADDRESSES 50
TFTP SERVER DISABLED
ETHERNET DUPLEX MODE 0
TELNET ACCESS ENABLED
ALLOW SCPC SESSIONS TRUE
ALLOW MPDS SESSIONS TRUE
ALLOW BGAN SESSIONS TRUE
ACCESS CONCENTRATOR NAME DataIO
DEFAULT PPPOE SERVICE PacketData
ACCESS POINT NAME
AT WELCOME MESSAGE
HIT 'H' for MORE
VP BLOCK: MISSING
TOOL VERSION = XXXX
TOOL NAME = EMBEDDED ORT TOOL
TOOL PART NUMBER = jaytool
SECURE ORT PART NUMBER = sss123
USER ORT PART NUMBER = uuu456
SATELLITE TABLE:
REGION 0: AORW (W) 52.0W CLASSIC AERO SWIFT64
REGION 1: AORE (E) 15.5W CLASSIC AERO SWIFT64
REGION 2: POR (P) 178.0E CLASSIC AERO SWIFT64
REGION 3: IOR (I) 64.0E CLASSIC AERO SWIFT64
REGION 4: MTSAT (4) 142.5E CLASSIC AERO
REGION 5: APAC (5) 143.5E CLASSIC AERO BGAN
REGION 6: EMEA (6) 25.0E CLASSIC AERO BGAN
REGION 7: AMERICAS (7) 98.0W CLASSIC AERO BGAN