GPS Bluetooth Receiver IGO-08B User’s Guide Version 1.
FCC GUIDELINES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
Table of Content Introduction ................................................1 Features ......................................................1 Package content.........................................2 Hardware Description ................................3 Technology Specification ..........................5 Operation ....................................................
Introduction IGO-08B is a GPS receiver with Bluetooth interface adopts advanced ATMEL ANTARIS 4 Super Sense GPS IC, and built-in active antenna for high sensitivity to tracking signal, there’s also an external MMCX aerial terminal for users adding higher MMCX antenna. Easy operation with speed limit setting. The bright red LED lighten to remind driver while speeding could improve driver’s safety effectively.
Easy wireless Bluetooth transmission is available in 10 meters distance. Flexible design, easy connection with auto-navigation, motorcade control, AVL, personal navigation, tracking system and map service industry. Package content Please make sure of your package includes the following items, If any item is damaged or missing, please contact your dealer at once. 1. Bluetooth GPS receiver IGO-08B x 1 2. Lithium rechargeable battery x 1 3. USB cable x 1 4. Slipperiless pad x 1 5. Car charger x 1 6.
Hardware Description There are four LEDs to show different status: Bluetooth（Blue） Fast blink: Indicates this Bluethooth GPS is waiting for pairing or master device’ connection. Slow blink: Indicates this Bluetooth GPS is connecting successfully.
Circle LED (Red) Speeding display & Battery capacity display Charge socket Battery bolt Switch 1 ( ) Short press: GPS Heading function On/Off Switch 2 ( ) Long press: Speeding setting On/Off Short press: Speed limit adjusting key Press right key to increase Press left key to decrease Power switch Long press: Power On/ Off Short press: Power capacity display on circle LED MMCX Antenna Socket 4
Technology Specification Satellite receiving Receiving and tracking 16 satellites at the same time Receiving frequency: 1575.42MHz Receiving code: L1, C/A code Accuracy (Precision) General positioning: 2.5m CEP DGPS/SBAS: 2.0m CEP Acquisition Cold start: 34 sec (Average) Warm start: 33 sec (Average) Hot start: 1 sec (Min) Sensitivity: -158dBm (Super sense mode) Dynamics: Altitude: max. 18,000m (Max.) Velocity: max. 500m/sec (Max.) Acceleration. Max. +/-4g (Max.
Power supply: DC 5.0V 5% Power consumption 70mA (Average) Operating Temp. -10°C~ +60°C Storage Temp. -20°C~ +85°C Humidity 5%~95% Size: 64(L) x 41 (W) x 19 (H)mm Weight 54g (include battery) Battery: Nokia 6100 compatible (spec. 3.
Operation 1. How to use battery 1-1 Charging battery more than 8 hours Before first time using IGO-08B’s battery, user has to charge the battery more than 8 hours. Connect travel charger or car charger with this device DC5V charge socket. The Power LED（Red）lighten indicates charging, the red LED goes off indicates finish charging. 1-2. Battery capacity check Press the Power Switch for 1 second when the IGO-08B is power on; the circle LED shows battery capacity. Each LED equals 12.5% power.
after positioning successfully. 3. How to active Bluetooth enabled device There are many Bluetooth enable devices like PDA or Bluetooth dangle on the market, which direct connect with IGO-08B. Each one may have different Bluetooth setup procedure. Please refer to their user manual for detail instruction. Activate Bluetooth search and connect function of Bluetooth PDA or dangle. A virtual comport will be assigned after Bluetooth connection is successful.
5. Speed limit setting Initial speeding alarm setting was off. Press SW2 KEY 2 seconds for speed setting on/off, upward round LED sets default 60KM, each LED equals 10KM. Press 1 second of SW1 KEY and SW2 KEY for speed adjustment. Press SW1 to decrease speed; press SW2 to increase speed. The maximum speed is 130KM. (full round LED lighten equals 130KM). After speed limit setting, the round LED turns off for power saving.
3100553640 Version 1.0 Jan.
