BEFORE USING THIS PRODUCT ............................................................................................................................. 1 COMMUNICATION REGULATION ..................................................................................................................................... 1 IMPORTANT SAFETY INSTRUCTIONS ............................................................................................................................... 2 SAFETY INFORMATION ..................
Before Using This Product Communication Regulation FCC Compliance This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Safety Instructions Improperly use of this electronic device may cause injury to your body and damage the property as well. This LCD TV device has designed and manufactured to meet international industrial safety standard. Same as other home electronic devices, you need to operate this equipment carefully in order to obtain the best performance of this equipment and to ensure the safety of using it.
Safety Information This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation.
Maintenance and Precaution Do not remove the cover or back of the TV. Any unauthorized changes or modification to the product will void the user’s warranty. Do not place the TV in a closed compartment. This will overheat the TV. Turn off the product if liquid is accidentally spilled into the TV. Contact your local dealer for assistance. Do not expose the TV to rain or moisture. According to the industrial standards, when pulling the power cord from the outlet, hold the power plug instead of the cord.
Getting Started (Preparation) Distance recommendations: Avoid improper installation and never position the unit where ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Refer to the minimum distance guidelines shown for a safe operation. Cleaning the screen: The screen is coated with a special thin film to reduce reflection.
Introduction Your Television Supplied Accessories The following items come along with your LCD TV: 6
TV Control Functions 1 button (Beneath) button (profile) 1 MENU SOURCE 6 5 1 LED Indicators 2 POWER 3 －CH+ 4 －VOL+ 5 SOURCE 6 MENU –VOL+ 4 -CH+ POWER 3 2 The LED indicator light up in 2 different colours green, red. Each colours represent different status. Green - Power is on; Red - Standby. Press this button to turn the power on/standby. Press to change channel/when is menu mode, these acts as navigation keys.
Setting Up the Remote Control 1. Open the lid of your remote control battery compartment on the back of the remote control. 2. Insert two AAA batteries. Use the (+) and (-) marks to guide you. The (+) marks on your batteries correspond to the (+) marks on the compartment. The (-) marks on your battery correspond to the (-) marks on the compartment. Note: Do not mix new and old or different kind of batteries 3. Put the lid back onto the remote control battery compartment.
Remote Control Functions The table below explains each button’s function. 1 Power on/off. 2 Press these keys to change the channels. 3 VOL +/VOL - Press these keys to adjust volume. 4 0~9 Numerical keys to select desired channel Navigation keys in Setup menu. 5 Navigation keys in Setup menu. 6 OK Press this key to confirm selection. 7 RECALL Recall last channel. 8 MUTE Press this key to turn off the sound. Press the "MUTE" button again or press "VOL+/ VOL-" to enable sound.
Inputs and Outputs Your LCD TV has five types of video connections. You should capitalize Cables on the best connection available from your LCD TV to get the best 1.RCA composite video cable 2. S-video cable display quality. For example, if you have a progressive DVD player that supports a component video connection, you should connect the DVD player to your LCD TV using component video connections instead of 3. RCA component video cable 4. RGB (VGA) video cable 5.
Connecting the Antenna or Analog Cable TV (CATV): 1. Disconnect the TV from all power sources before making any connections. 2. Use the coaxial cable (75 ohms) for connecting TV signal from your antenna or cable TV provider to the tuner input. 3. Hook up the cable to the TUNER input in the rear of the LCD TV. 4. Connect the power cord of the LCD TV to a power outlet. 5. Press the “SOURCE” button on either the remote control or the TV controls and select TV on the source menu.
6. Press the “MENU” button on the remote control to display the OSD menu use ▲▼ or ◄► to navigate through the icons. In the first option (Channel), press “OK”. Choose the first option “Tuner Mode” and press “OK”. If your TV is connected to the antenna, choose Air. If your TV is connected to the cable television outlet, choose Cable. (For more information on the Channel menu, refer to Page 23.) 7. Then choose STD and press “OK” STD-Standard HRC-Harmonic Related Carrier IRC-Incremental Related Carrier 8.
Connecting the Digital Set-Top Box (Commonly Used For HDTVs, Satellite TVs, etc.): 1. Disconnect the TV and set-top box from all power sources before making any connections. 2. Use a HDMI cable, component video cable, or S-video cable to connect the HDMI, COMPONENT, or S-VIDEO output jacks of your digital set-top box to the HDMI, COMPONENT, or S-VIDEO input jacks in the rear of the LCD TV. 3.
5. Press the “SOURCE” button on either the remote control or the TV controls. Select AV1(S-Video)/AV1(CVBS)/ YPbPr1 /YPbPr2/HDMI, depending on which input is the digital set-top box connected to. (Changing the source, refer to Page19) Note: 1. It is strongly recommended that the user connects Digital Set-Top Box via HDMI connection if provided. HDMI signal is pure digital signal; therefore, it gives the best performance for HD programs. 2.
Connecting the Component Video: To connect your progressive DVD player or HD DVD Player via component video: 1. Connect the green Y jack on the back of your DVD player to the green component Y jack on the rear of the LCD TV. 2. Connect the red Pr/Cr jack on the back of your DVD player to the red Pr/Cr jack on the rear of the LCD TV. 3. Connect the blue Pb/Cb jack on the back of your DVD player to the blue Pb/Cb jack on the rear of the LCD TV. 4.
Connecting the S-Video or Composite Video: This section shows you how to connect devices to the S-video and composite video inputs of your LCD TV. Most devices like VCRs, camcorders, non-progressive scan DVD players, etc only provide composite video output or S-video output. The steps below are to show you how to connect two devices simultaneously. 1. Connect the S-video on the back of your camcorder to the S-video under AV Input jack. 2.
Connecting the PC: 1. If you wish to connect a PC to the LCD TV, connect the 15-pin D sub RGB connector on your PC to the PC connector on the rear of the LCD TV. 2. Connect the audio output on your PC to the PC audio input on the rear of the LCD TV. 3. Press the “SOURCE” button on the remote control to select “VGA”. 4. You may configure your PC’s VGA resolution to optimized resolution on the LCD TV. The recommended resolution of the LCD TV is 1024 x 768.
Connecting the HDMI: 1. Use a HDMI cable to connect the HDMI output jack of your external device to the HDMI input jack in the rear of the LCD TV. 1. Press the “SOURCE” button on either the remote control or the TV controls. Select HDMI. (Changing the source, refer to Page 19) Note: HDMI connection includes both digital audio and video signals.
Setting Up Your Television Changing the Source 1. Press the “SOURCE” button on either the remote control or TV controls. 2. Repeat it according to selecting until wanting of “source”. TV→AV1(CVBS)→AV1(S-Video)→YPbPr1→YPbPr2→HDMI→VGA Note: When the source has no signal to input, TV will be “Auto Power off” after 15 minutes.
Aspect When the input is 4:3 (the image dimension usually used by cable television, and video cassette), the user might want to eliminate the “black spots” on the left and the right of the screen. By doing this, the user might choose WIDE SCREEN, which distorts image by stretching the whole image horizontally In most cases, widescreen videos (such as DVD movies’ widescreen modes) will have “black spots” on the top and the bottom of the screen (this is called letterbox).
Accessing the OSD (On Screen Display) Menu 1. Press “MENU” on the remote control to start the OSD menu. 2. Use ▲▼◄► to navigate through the main function. 3. Press ► or “OK” to enter the highlighted category. 4. Use ▲▼ to navigate 5. Press “MENU” or ◄► to change the selected settings. 6 Press “EXIT” to exit the OSD menu or press “MENU” to switch to previous step.
Icon Description There are 5 main functions (Channel, Picture, Sound, Functions, Setup) in the OSD menu. Before you start using the OSD menu, it is recommended that you read through the following icon descriptions.
Channel How to set the parameters in the Channel menu Function Tuner Mode Auto Scan Channel Edit Description Options This allows the user to switch between Air Air(Analog antenna)/Cable(Cable and cable TV. TV) The auto scan helps the user to search for available channels on television. This option allows the user to add/delete recognized channels.
Tuner Mode 1. Press MENU button. 2. Use ▲,▼ button to highlight“Channel” icon, then press “OK” 3. Use ▲,▼ button to make a choice from Air or Cable, then press “OK” 4. If choose cable, must choose STD, HRC or IRC again. Press EXIT to exit the menu screen. Press MENU button to switch to previous step on the menu screen.
Auto Scan 1. Press MENU button. 2. Use ▲,▼ button to highlight “Tuner Mode” icon, then press “OK”. 3.Choose the “Air” and press “OK” 4. Use ▲,▼ button to highlight “Auto Scan” icon, then press “OK”. (Scan “Digital channel” after Analog channel” finish.) 5.It will automatically scan and store all of the channels that are available in your local area. (To stop the auto searching, press “OK” button.) 6. The scanned channel is displayed when done. 7.
Channel Edit 1. Press MENU Button. 2. Use ▲,▼ button to highlight“Channel” icon, then press “OK”. 3. Press ▲,▼ button to highlight “channel Edit” icon, then press “OK” 4. Use ▲,▼/◄,► button to select channels. Selected channels will be yellow colored. Then press “OK”button to add or delete channels. If channels added, user can see the “√”mark 5.Press “OK” button to add channels to the Favorite Channel, and press again to cancel adding.
Signal Strength 1. Press MENU button. 2. Use▲,▼ button to highlight “Channel”icon, then press “OK”. 3. Use ▲,▼ button to highlight “Signal Strength” icon, then press “OK”. •Less than 50, unacceptable to watch •50~79, not stable •More than 80, no problem in watching TV Press EXIT to exit the menu screen. Press MENU button to switch to previous step on the menu screen.
Picture Adjusting contrast, brightness, color, tint, or sharpness requires the user to switch the mode to “user”. While adjusting customized selections, only the selection and its status bar will be shown on the screen. Example: 1.Use ▲or▼ to “Picture Mode” and press “OK” 2.Use ▲or▼ to “User” and press “OK” 3.Press ▼ to brightness and press “OK” or ► to select 4. Press ◄► to adjust the brightness. 5. Use ▲or▼ to adjust R,G,B Value Separately.
How to set the parameters in the Picture mode menu. Function Brightness Description Mode is the selection that allow the user to choose among default video settings and customizable video settings. Adjusts the brightness. 0-100 Saturation Adjusts the color 0-100 Contrast Adjusts the contrast. Sharpness adjusts increase or reduce the picture performance sharpness. Tint adjusts the natural aspect 0-100 Picture Mode Sharpness Tint RGB of a color.
Sound How to set the parameters in the Sound menu . Function Sound Mode Treble Bass Balance AVL Audio Language Digital Audio Out Description User selects and enjoy sound mode made by factory in the favor of user’s. In Standard, Movie, music and Speech mode. If changing the value of Treble, Base, Balance, go to user mode automatically. Adjusts the higher pitched sounds. Adjusts the lower pitched sounds. Adjusts the "position" of the sound.
Functions Auto Lock 1. Press MENU button. 2.Use▲,▼/◄,► button to highlight“Functions” icon, then press “OK” 3.Choose the “Auto Lock” and press “OK” or “►". 4.When the “Enter PIN” box pops up, enter the 4 digit password The default password is 0000 Set Blocking 1. After get released, use ▲,▼ button to highlight “Set Blocking” icon, then press “OK” 2. Use ▲,▼ button to make a choice Either ”ON” or ”OFF”, then press Channel Blocking 1.
Block by Rating 1.Use ▲,▼ button to highlight “Block by Rating” icon, then press “OK”. 2. Use ▲,▼ button to make a choice, then press “OK”.
DTV Rating 1. Use ▲,▼ button to highlight “DTV Rating”, then press “OK”. This function works only in DTV input. Setup Code 1.Use ▲,▼ button to highlight “Setup Code”, then press “OK” 2．When the box pops up, enter the new password and confirm it with entering the same number once more Press EXIT to exit the menu screen. Press MENU button to switch to previous step on the menu screen.
Caption 1. Press MENU button. 2. Use ▲,▼ button to highlight “Functions” icon, then press “OK” 3. Use ▲,▼ button to highlight “Caption”icon, then press “OK” 4. Use ◄,► button to highlight “Display”Always On or Off, then press “OK” 5. When “Display” is “Always On” user can choose the “Service” icon 6.Use ▲,▼ button to highlight "Service". 7.
Caption Option 1. Use ▲,▼ button to highlight “Caption Option”, then press “OK” 2. Use ◄,► button to make a choice, either “Auto” or “Options”, then press “OK” If choosing “Auto”, CC background and Option Text is not activated, And will follow CC saved in broadcasting information If choosing “Options”. CC background and Option Text is activated. CC Background 1.Press MENU button. 2.Use ▲,▼ button to highlight“Functions” icon, then press “OK” 3.
Caption Text 1. Use ▲,▼ button to highlight “Caption Text”, then press “OK” 2. When the box pops up, highlight the box (Ex. Size, Style.) that you want to make a change, then use ◄,► button to see the choices 3.
Setup Date/Time 1. Press Menu Button 2.Use ▲,▼ button to highlight “Setup”,then press “OK” 3.Use ▲,▼ button to highlight “Date/Time”, then press “OK” 4. Choose the "Manual", then press" OK " 5. Use ▲,▼/◄,► button to set for Date/Time Power on Time 1. Press Menu Button 2. Use ▲,▼ button to highlight “Setup”,then press “OK” 3. Use ▲,▼ button to highlight “Power on Time”, then press “OK” 4. Choose the "Activate", then press " OK ". The user can choose the follows: Off→ Daily →Once 5.
Power off Time 1. Press MENU Button 2.Use ▲,▼ button to highlight “Setup”, then press “OK” 3. Use ▲,▼ button to highlight “Power off Time”, then press “OK” 4. Choose the "Activate", then press " OK ". The user can choose the follows: Off→ Daily →Once 5. Choose the "Time", then press " OK ". The user can set the time of power off Sleep 1. Press MENU button 2. Use ▲,▼ button to highlight “Setup” icon, then press “OK” 3. Use ▲,▼ button to highlight “Sleep” icon, then press “OK” 4.
Menu Opacity 1.Press MENU Button 2.Use ▲,▼ button to highlight “Setup”,then press “OK” 3.Use ▲,▼ button to highlight “Menu Opacity”, then press “OK” 4.Use ◄,► button to set for “Menu Opacity”. Emergency Alert 1.Press MENU Button 2.Use ▲,▼ button to highlight “Setup”,then press “OK” 3. Use ▲,▼ button to highlight“ Emergency Alert”, then press “OK” 4. Choose the "Low" or "Medium", then press " OK " 5. Use ◄,► button to set for "Present" or "Discard", then press " OK " Press EXIT to exit the menu screen.
PC 1. Press MENU Button 2. Use ▲,▼ button to highlight “Setup”,then press “Select” 3. Use ▲,▼ button to highlight “PC”, then press “Select” 4. Choose the "Auto Adjust", then press "SELECT". Return to the factory default 5. Choose the "Hor. Center", then press "SELECT". User can adjust horizontal position. 6. Choose the "Ver. Center", then press "SELECT". User can adjust vertical position. 7. Choose the “Phase”, then press “SELECT”.
Basic Troubleshooting Read this section to learn how to maintain and troubleshoot your LCD TV Problem Possible Solution 1.Make sure the power plug is properly There is no picture or sound connected to the power outlet. 2.The channel may not have been scanned and can be re-scanned again from the setup OSD menu. 3.Make sure you have selected the correct input mode. There is just noise 1.The antenna reception strength may be weak. 2.Reposition the antenna's placement. 3.
Problem Possible Solution No picture, there is sound. 1. Check to see if the video cable is properly connected. 2. Press the "SOURCE" button from the remote control to see if the input is correctly selected. ● There is no sound. 1. Make sure the volume level is not set to the minimum. 2. Make sure the mute function is not selected. The picture is not sharp. 1. The program reception may be weak . 2. Check the "Sharpness" setting in the OSD video menu.
General Specifications LCD Panel Input/Output Audio Compatibility Compatibility Screen Size 32" diagonal Resolution Display Color Aspect Ratio WXGA (H) 1366 X (V) 768pixels 16, 777, 216 Color 16：9 WIDE Video in/ out 1 Vp-p/75 Ω S-VIDEO in Y 1 Vp-p/75 Ω, C 0.7 Vp-p/75 Ω Y / Pb/Cb / Pr/Cr Y 1 Vp-p/75 Ω, Cb/Pb / Cr/Pr 0.
Pictures for different crust ① ② ③ 44
RGB Frequency Table The table below shows the frequency ranges supported by the LCD TV. It supports from VGA to XGA. If you are connecting your PC to the LCD TV via the RGB port, please use the following table in order to setup your PC’s VGA output for maximum optimization.
