Installing the LCD TV Using the LCD TV 32 LCD TV User Guide POWER MUTE COMP. PC POP DIGEST TV VIDEO WIDE PIP - + DISP V-CHIP C.C.
Federal Communications Commission Statement Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user authority to operate the equipment. FCC 1 ENGLISH This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Warnings and Precautions To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing and maintenance of this equipment. Before operating this equipment, please read this manual completely, and keep it nearby for future reference. WARNING This symbol is intended to alert the user to avoid the risk of electric shock. This equipment must not be disassembled by anyone except qualified service personnel.
Remove the plug from the wall outlet, if the equipment will not be used for a long period of time. ▪ Do not place, use or handle this equipment near water. ▪ Never expose the equipment to liquid, rain, or moisture. Seek for service if any of the above is spilled into the equipment. ▪ Do not expose the equipment to extreme temperature or to direct sunlight, as the equipment may heat up and suffer damage.
Outdoor Antenna Safety Instructions If an outdoor antenna is connected, follow the precautions below: ▪ An outdoor antenna should not be located in any area where it could come in contact with overhead power lines, or any other electric light or power circuits. ▪ When installing an outdoor antenna system, extreme caution should be taken to prevent contact with power lines. Direct contact with power lines may be fatal and should be avoided at all costs.
CONTENTS ENGLISH Federal Communications Commission Statement Warnings and Precautions Important Safety Instructions ......................................................................................... 2 Antenna Safety Instructions ........................................................................................... 4 Chapter 1 Introducing the LCD TV Key Features .................................................................................................................
6 Chapter 1 Introducing the LCD TV
Chapter 1 Introducing the LCD TV Key Features ENGLISH Various Audio/Video terminals for external equipment connection ▪ ▪ ▪ ▪ ▪ 1 set of composite A/V terminals 1 S-VIDEO terminal 1 set of component Video input terminals 1 VGA input terminal 3 sets of Audio input terminals Digital Noise Reduction ▪ This function can digitally reduce image noise to provide better picture quality.
Package Contents Make sure all of the following contents are included. If you are missing any items, please return this product to the original place of purchase. LCD TV Power Cord Remote Control/AAA Batteries x 2 Auto Tune POWER D1/D2/D3 SCART AV S-VIDEO COMP. TV PIP SOURCE DVI FAV. V-CHIP R VGA C.C.
Setting Your LCD TV Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal (refer to page11). ENGLISH Connect the AC power cord at the back of the TV and connect t the power cord to wall outlet. Insert the 2 batteries supplied in remote control. Step1 Slide the back cover up to open the battery compartment of the remote control. Step2 Insert two AAA size batteries.
Your LCD TV Front/Top View and Controls LED The LED light indicates when the LCD TV is activated. IR Infrared Receiver (IR) MENU Press once to display the OSD (on screen display), press again to turn the OSD off. Turns the LCD TV on and into standby mode. SOURCE Chooses from different input signal sources. SELECT▲▼ Scans up and down through channels. Selects sub-menu item when in the OSD mode. VOLUME◄► Adjusts the volume up and down.
Rear View and Jacks ENGLISH D-SUB Connects the satellite receiver or other AV equipment, TV Box, or PC with D-Sub connector. COMPONENT(YPbPr) Connects to the Component(YPbPr) video and audio output jacks on external video equipment. COMPONENT(YCbCr) Connects to the Component(YCbCr) video and audio output jacks on external video equipment. AV Connects to the composite Video and Audio output jacks on external video equipment.
Your Remote Control SWAP PICTURE Swaps between main and sub screens in PIP/POP/ DIGEST mode. Cycles through picture quality modes: STANDARD, BRIGHT, SOFT, MOVE STANDARD, MOVE BRILLIANT MUTE MUTE Mutes and restores your LCD TV sound. POWER TV/CATV PICTURE SWAP SOUND TV/CATV Cycles through the TV receiving signal: TV(antenna), CATV(cable) WIDE Cycles through the picture size: 16:9, 4:3, FULL, NATURAL -+ Changes the size of secondary picture while using the window button. TV VIDEO COMP.
Chapter 2 Installing the LCD TV Connecting a TV Cable or Antenna Antenna Connection The antenna requirements for good color TV reception are more important than those for a black & white TV reception. For this reason, a good quality outdoor antenna is strongly recommended. The following is a brief explanation of the type of connection that is provided with the various antenna systems.
A. Combination VHF/UHF antenna VHF/UHF Antenna 300/75-ohm adapter (not included) 300-ohm twinlead cable VHF/UHF Antenna 75-ohm coaxial cable UHF Antenna B.
Cable TV (CATV) Connection ENGLISH This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building accurately, or as close to the point of cable entry as possible.
Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal. Connect the AC power cord at the back of the TV and connect t the power cord to wall outlet. Press the button on the remote to turn on the LCD TV. Always disconnect the LCD TV from the main voltage when the LCD TV will not be used for a long period of time. The POWER button on the front panel is only used for switching the LCD TV into standby, it does not disconnect the device from the main voltage.
Connecting a VCR ENGLISH Pb D-SUB (VGA) Pr A B METHOD A: Use an audio cable to connect the VCR’s audio output jacks to the LCD TV’s audio inputs. Use an S-Video cable to connect the VCR’s S-video output jack to the LCD TV’s S-video input jack. METHOD B: Use a composite cable to connect the VCR’s composite video/audio jacks to the LCD TV’s composite video/audio jacks. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment.
Connecting a DVD Player Pb D-SUB (VGA) Pr B METHOD A: C A DVD PLAYER Use a component cable to connect the DVD player’s component (YCbCr) output jacks to the LCD TV’s component input jacks. Use an audio cable to connect the DVD player’s component audio jacks to the LCD TV’s audio input jacks. METHOD B: Use an audio cable to connect the DVD’s audio output jacks to the LCD TV’s audio inputs. Use an S-Video cable to connect the DVD’s S-video output jack to the LCD TV’s S-video input jack.
Connecting a TV Cable Box and Satellite Receiver ENGLISH Pb D-SUB (VGA) Pr A B Use a component cable to connect the satellite receiver’s component (YPbPr) output jacks to the LCD TV’s component input jacks. Use an audio cable to connect the satellite receiver’s component audio jacks to the LCD TV’s audio input jacks. METHOD A: Use an audio cable to connect the TV Cable Box’s audio output jacks to the LCD TV’s audio inputs.
Press the To watch programs via satellite receiver, press the YCbCr button on the remote. 20 Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. button on the remote to turn on the LCD TV. To watch TV via TV cable box, press the VIDEO button on the remote repeatedly to select S-VIDEO( METHOD A), or PC (Method B) .
Connecting a Video Camara ENGLISH Pb D-SUB (VGA) Pr A B METHOD A: Use an audio cable to connect the video camera’s audio output jacks to the LCD TV’s audio inputs. Use an S-Video cable to connect the VCR’s S-video output jack to the LCD TV’s S-video input jack. METHOD B: Use a composite cable to connect the video camera’s composite video/audio jacks to the LCD TV’s composite video/audio jacks.
Connecting two VCRs Pb D-SUB (VGA) Pr Use a composite cable to connect the VCR’s composite video/audio input jacks to the LCD TV’s composite video/audio output jacks. Use a composite cable to connect the VCR’s composite video/audio outputjacks to the LCD TV’s composite video/audio input jacks. Connect all AC power sources, before turning the LCD TV’s power switch on. Press the button on the remote to turn on your LCD TV. Through connected two VCRs, you can record one VCR to the other.
Connecting a PC ENGLISH Pb D-SUB (VGA) Pr Use a D-SUB cable to connect the PC’s D-SUB output jack to the LCD TV’s VGA input jack. Use an audio cable to connect the PC’s audio output jacks to LCD TV’s. Connect all AC power sources, before turning on the power switch of the LCD TV or other connected equipment. Press the button on the remote to turn on the LCD TV. Press the PC on the remote.
24 Chapter 3 Using the LCD TV
Chapter 3 USING THE FEATURES Press the ENGLISH Watching Your LCD button to turn the LCD TV on. Press the TV button to enter TV mode, or press the SOURCE button on the front of TV to select the TV. MUTE POWER TV/CATV PICTURE SWAP TV VIDEO WIDE PIP - + DISP V-CHIP C.C. R G Y 1 SOUND COMP. PC POP DIGEST 2 Press the CH▲▼ buttons to change channels, or use the 0-9 buttons to choose a channel. The one/two digit numbers by pressing -/-button.
Operating the Menu Press the button to turn the LCD TV on. To select the signal source, press the MENU button on the remote control. The main menu will appear on the screen. Use VOL- VOL+ to select your main menu option.
DISPLAY MENU: MAIN MENU : DISPLAY FULL TV VGA ► ENGLISH DISPLAY MODE: MAIN SOURCE: SUB SOURCE: SWAP MENU SELECT PIP H POSITION PIP V POSITION ► ► : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT OSD MENU: MAIN MENU : OSD LANGUAGE TRANSPARENCY OSD TIME OUT ENGLISH 8 15 SEC : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT MISCELLANEOUS MENU: MAIN MENU : MISC SLEEP ASPECT RATIO NOISE REDUCTION IMAGE FREEZE CCD TYPE CCD : SELECT MENU : EXIT OFF FULL MEDIUM OFF CC1 OFF : SELECT ITEM ENTER: NEXT TV SET
Setting up the Channel List Automatically scans and stores all the TV channels With the LCD TV connected to a television programming source, press the TV button on the remote control. Press the MENU button on the remote control to display the Main menu, and use VOL- VOL+ to select the TV SET, and press the ENTER button. MAIN MENU : TV SET CH MODE CHANNEL EDIT FAVORITE STATION STATUS MTS CH SCAN : SELECT MENU : EXIT NORMAL 46 ► CATV ADD MONO ► : SELECT ITEM ENTER: NEXT CH+ Press or CATV.
Hiding the TV channels CH+ to select the TV SET, and press the ENTER button. CH- ENGLISH Press the MENU button on the remote control to display the Main menu, and use CH+ Press to select CHANNEL, then press the VOL+- to select the channel you choose to hide.
Setting the Favorite TV channels CH+ Press the MENU button on the remote control to display the Main menu, and use CH- to select the TV SET, and press the ENTER button. MAIN MENU : TV SET CH MODE CHANNEL EDIT FAVORITE STATION STATUS MTS CH SCAN NORMAL 46 ► CATV ADD MONO ► : SELECT MENU : EXIT Press : SELECT ITEM ENTER: NEXT to select EDIT FAVORITE, and press the ENTER button.
Customizing the Picture Settings Press the button to turn the LCD TV on. ENGLISH Press the MENU button to display the Main Menu : MAIN MENU : IMAGE BIRGHTNESS CONTRAST SATURATION HUE SHARPNESS PHASE PREQ 29 35 22 0 16 0 0 : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT Press ▼, the other item will appear on the screen.
32 H POSITION Controls the horizontal position of the picture. V POSITION Controls the vertical position of the picture. AUTO ADJUST Allows adjustment for the fine tune level by hand if signal is too weak or picture is blurry. IMAGE MODE This setting controls the overall appearance of the picture, and is chosen from among the following options: STANDARD, BRIGHT, SOFT, MOVE STANDARD, MOVE BRILLIANT. RESET Restores the original factory settings.
Customizing the Audio Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press VOL- VOL+ ENGLISH to select AUDIO. MAIN MENU : AUDIO BASS TREBLE BALANCE VOLUME 11 11 0 11 ► RESET : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT CH+ Press to select the item to control, then press ENTER button to enter into adjustment mode. CH- Press VOL- VOL+ to adjust the desired value. BASS Controls the relative intensity of lower-pitched sounds.
Customizing the Picture Color Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press VOL- VOL+ to select RGB. MAIN MENU : RGB COLOR TEMP RED GREEN BLUE RESET USER ► : SELECT MENU : EXIT : SELECT ITEM ENTER: NEXT CH+ Press mode. Press to select the item to control, then press ENTER button to enter into adjustment CH- VOL- VOL+ to adjust the desired value.
Customizing the DISPLAY Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press VOL- VOL+ ENGLISH to select DISPALY. MAIN MENU : DISPLAY DISPLAY MODE: MAIN SOURCE: SUB SOURCE: SWAP MENU SELECT PIP H POSITION PIP V POSITION : SELECT MENU : EXIT FULL TV VGA ► ► ► : SELECT ITEM ENTER: NEXT CH+ Press to select the item to control, then press ENTER button to enter into adjustment mode. CH- Press VOL- VOL+ to adjust the desired value.
Customizing the OSD Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press VOL- VOL+ to select OSD. MAIN MENU : OSD LANGUAGE TRANSPARENCY OSD TIME OUT : SELECT MENU : EXIT 36 ENGLISH 8 15 SEC : SELECT ITEM ENTER: NEXT CH+ Press mode. CH- to select the item to control, then press ENTER button to enter into adjustment CH+ Press CH- to adjust the desired value.
Customizing the MISC Settings Press the button to turn the LCD TV on. Press the MENU button to display the Main Menu.Press VOL- VOL+ ENGLISH to select MISC. MAIN MENU : MISC SLEEP ASPECT RATIO NOISE REDUCTION IMAGE FREEZE CCD TYPE CCD : SELECT MENU : EXIT OFF FULL MEDIUM OFF CC1 OFF : SELECT ITEM ENTER: NEXT CH+ Press to select the item to control, then press ENTER button to enter into adjustment mode. CH- CH+ Press CH- to adjust the desired value.
Customizing the PIP/POP/DIGEST Settings The PIP/POP/DIGEST feature allows simultaneous viewing of video from two sources (TV, VCR, DVD etc). Only one source’s audio is played at a time; the user may select which source’s audio is Press the PIP button on the remote control to enter picture-in-picture mode, press again to exit PIP mode. MAIN SUB Press the POP button on the remote control to enter picture-outside-picture mode, press again to exit POP mode.
Customizing the V-CHIP Settings Press the V-CHIP button on the remote control to display the Main menu: PARENTAL CONTROL INPUT 4 DIGITS PIN NUMBER ____ PRESS 0...9 V-CHIP: EXIT Use the PARENTAL CONTROL function, must enter a four-digit password. The factory password is 0000. CH+ Use to select the PARENTAL CONTROL, then Use option to turn the PARENTAL CONTROL functions on.
The TV GUIDELINE has 2 rating methods: Content-Based Rating and Age-Based Rating.
Setting the New Password Press the V-CHIP button on the remote control to display the Main menu: ENGLISH PARENTAL CONTROL INPUT 4 DIGITS PIN NUMBER ____ PRESS 0...9 V-CHIP: EXIT Use the PARENTAL CONTROL function, must enter a four-digit password. The factory password is 0000. CH+ Press mode.
42 Troubleshooting and Specifications
TROUBLESHOOTING TROUBLESHOOTING ENGLISH Before consulting service personnel, check the following chart for a possible cause of the trouble and for a possible solution. TV will not turn on Make sure the power cord is plugged in, then press the button on the remote. The batteries in the remote control may be exhausted. Replace the batteries. No picture, no sound Check the interface cable between TV and antenna/cable TV. Press the button on the remote.
SPECIFICATION TROUBLESHOOTING Panel System 32 inch Display Resolution 1366 pixels(horizontal) x 768 pixels (vertical) Television System NTSC Antenna Input 75 Ω unbalanced AV IN 1 AV OUT 1 SV 1 YCbCr YPbPr 1 1 VGA 44 1 AUDIO IN 3 AUDIO OUT 1 SPEAKER OUT 10 W x 2 POWER SOURCE (Power consumption(Max)) 200 W DIMENSION 970 mm (W) x 585 mm (H) x 300 mm (H) WEIGHT 21 KG Troubleshooting and Specifications
