Owner's Manual

12
FIRE MODE - Choose between the different firing modes
• The current Firing Mode setting is displayed on the right side of the screen.
• Press CENTER or RIGHT to change the Fire Mode setting
• Press UP or DOWN to cycle through Firing Modes
• Press CENTER or LEFT to save your selection
• SEMI - Semi automatic firing shoots 1 shot per trigger pull up to the max ROF
(Rate of Fire) setting
• RAMP – Semi auto shots (equal to Ramp Shot Start setting), then a Ramping
rate of fire up to the max ROF setting (if Ramp Sustain Trigger Pulls
per Second is achieved, see below)
• BURST – Semi auto shots (equal to Ramp Shot Start setting), then multiple-
shot bursts at the max ROF. The number of shots in the burst is adjustable in
the BURST SHOT setting. If time between shots is longer than Ramp
Reset setting the marker goes back to Semi Automatic and the Ramp Start shot counter
is reset.
• AUTO - Semi auto shots (equal to Ramp Shot Start setting), then Fully Automatic firing
at the ROF CAP setting. If time between shots is longer than the Ramp Reset setting the
marker goes back to Semi Automatic and the Ramp Start shot counter is reset.
• PSP BST 12 - Complies to 2010-2012 PSP rules using Burst mode as described above
• PSP RMP 12 - Complies to 2010-2012 PSP rules using Ramp mode as described above
• PSP BST 10 - Complies to 2014 PSP Champions/Challengers rules using Burst mode as
described above
• PSP RMP 10 - Complies to 2014 PSP Champions/Challengers rules using Ramp mode as
described above
• MILL - Complies to 2010-2012 Millennium Series Rules using Ramp mode as
described above
• NPPL – Complies with 2012 NPPL rules using Semi Auto mode as described
above
ROF CAP - Choose between having the marker Rate of Fire Capped or Un-
capped. Turning this setting ON will cap the marker at the ROF (•) ON setting.
Turning this setting OFF will uncap the marker and allow the marker to fire as
fast as paintballs can be loaded and detected by the eyes.
Note - Firing modes other than Semi may not be uncapped due to ASTM Safety
Regulations.
• The screen displays the current setting of whether ROF CAP is On or OFF
• Press CENTER or RIGHT to change the ROF Cap setting
• Press UP or DOWN to cycle through ON or OFF
• Press LEFT or Press CENTER on D-Pad to save the setting and return to
CONFIG menu
ROF (•) ON- The maximum Rate of Fire with Eyes On (ROF Cap must be ON)
• The screen displays the current ROF EYES ON setting
• Press RIGHT or Press CENTER on D-Pad to change the ROF with EYES ON
setting
• Press UP or DOWN to increase/decrease the BPS setting (8.0-25.0 BPS, in
0.1 BPS increments)
• Press LEFT or Press CENTER on D-Pad to save setting and return to CONFIG
menu
ROF (•) OFF - The maximum Rate of Fire with Eyes OFF
• The screen displays the current ROF EYES OFF setting
• Press RIGHT or Press CENTER on D-Pad to change the ROF with
EYES OFF setting
• Press UP or DOWN to increase/decrease the BPS setting
(8.0-25.0 BPS, in 0.1 BPS increments)
• Press LEFT or Press CENTER of D-Pad to save setting and return
to CONFIG menu
ROF Default - The maximum allowed Rate of Fire if the eyes become dirty or malfunction.
• The screen displays the current ROF Default setting (in BPS)
• Press RIGHT or Press CENTER on D-Pad to change the ROF
Default setting (default is 8 BPS)
• Press UP or DOWN to increase/decrease the BPS setting (7-12 BPS, in 1
BPS increments)
• Press LEFT or Press CENTER of D-Pad to save setting and return to CONFIG menu