O P E R AT O R ’ S M A N U A L 1
This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years of age or older to purchase. Persons under 18 years of age must have adult supervision. READ THIS MANUAL BEFORE USING.
- Action: Electro-pneumatic - Air Source: Compressed Air Only - Battery: One 9-Volt Alkaline - Cycle Rate: 25.0 BPS - Main Material: Aluminum - Accuracy Range: 150+ ft - Weight: 2.00 lbs. (908 grams) Included with your Empire Syx - 14” Aluminum 2pc Barrel (.688 bore) - Hex Keys - Spare Parts Kit - Barrel Sleeve - One 9-Volt Battery - Marker Case 1. Basic Operation Barrel Installation 1. Make sure marker is degassed, loader removed, no paintballs in the feed port or breech and the marker is OFF. 2.
Live Mode. The battery icon will show the power level remaining in the battery. • Remove the Barrel from the Syx. • Locate the Locking Button at the bottom of the barrel opening in the Body (Fig. 1-1). • While pressing and holding the Locking Button, pull the front section of the Foregrip forward and away from the rest of the Foregrip to access the interior and battery. • Attach the 9-volt battery to the Battery Harness following the polarity markings and place within the Foregrip.
Regulator Adjustment If air pressure adjustments are needed use a 3/32in. hex wrench and insert it into the regulator adjustment screw (the single hole closer to the front on the bottom of the ASA) (Fig. 2-1). - To Increase pressure, turn Counter-Clockwise. - To Decrease pressure, turn Clockwise. (Fig. 2-1) Note: Do Not Use CO2! The input pressure affects the paintball velocity, so the same process listed above is used to adjust the velocity.
MAIN MENU Press the D-pad to the UP or DOWN directions to scroll through the MAIN Menu options. Press and hold the Bottom button to make a selection. • OFF – Turns Marker Off • CONFIG – Enters User CONFIGurations Menu (see below) • SYSTEM – Enters SYSTEM Settings Menu (see page 5) • EXIT – Exits back to LIVE Mode MENU QUICK EXIT As long as you are not currently modifying a setting, you can exit any menu at any time by pressing and releasing the trigger. This will take you back to LIVE Mode.
this setting for use with faster feeding loaders to increase max ROF. - Press and Hold the Bottom button to see current Ball In Place setting (in milliseconds) - Press UP or DOWN buttons to increase/decrease the BIP setting (1-20ms) - Press and Hold the Bottom button to save setting and return to CONFIG menu Anti-Bolt Stick Wait Time- Time that must expire after a shot before ABS is activated. Helps prevent first shot drop-off.
Auto Off – The elapsed time after the last trigger activation in which marker will shut off to save power.
through the holes between the O-rings. (Fig. 4e Slide and snap the Main Spring onto the Bolt, one end of the spring is smaller and will lock onto the Bolt. Slide the Bolt with Main Spring onto the Bolt Guide Front. Insert the Bolt System assembly into the back of Body and lock into place. (Fig. 4e) Bolt System maintenance is now complete. Note that a velocity adjustment over a paintball chronograph may be necessary after performing Bolt System maintenance.
INSTALLATION OF GRIP FRAME AND TRIGGER GUARD - Attach Trigger Guard to Grip Frame by the two screws using a 3/32” hex wrench, one on top of the Grip Frame the other on the Grip area. - Attach the Body to the Grip Frame. Four screws hold the Grip Frame to the Body and must be reinstalled. 1. One screw each side of the Foregrip, install using a 5/64” hex wrench. 2. Use a 3/32” hex to install the screw in front of the Trigger Guard, near the Foregrip 3.
4. 5. 6. Inspect each O-ring at the bottom of Solenoid threads (labeled A) and the top of Solenoid (labeled B) for damage, replace as necessary (see Figure 6c). Remove the 3 small screws on the top of the Solenoid using a 1/16” hex wrench (see Figure 6d). Lift the top cap off the Solenoid to expose the Solenoid Piston. Be careful not to lose the small O-ring at the top of the Solenoid, it may be stuck to the top cap (labeled A in Figure 6e). If O-ring is damaged, replace it. 7.
WARRANTY INFORMATION G.I. Sportz is dedicated to providing you with products of the highest quality and the industry’s best product support available for satisfactory play. G.I. Sportz 2955 Adams Center Road Fort Wayne, IN 46808 www.GISportz.com G.I. Sportz Paintball is a brand of G.I. Sportz Direct, LLC. PATENT(S): See www.paintballsolutions.com/patents © 2018 G.I. Sportz. All rights reserved. This G.I. Sportz product is protected by one or more United States patents. G.I.
