Manual

12
Markerdoesnotre/cycle Markermaynotbeturnedon Checkscreenonrearofforegrip.OLEDscreenshouldbeonwhen
markeristurnedon.
Paintballs may not be fed into breech Theanti-chopeyesystempreventsthemarkerfromringunlessa
ball is present. When the eyes detect a ball the eye symbol on the
screenwillhavealledcircleinthemiddle.Neverputanything
otherthanapaintballdownthefeedneckoftheMiniGS.Checkthat
the bolt is fully returning and if not service you may need to change
bolttip,smallboltguideo-ringsand/orthebolto-rings.Checkthat
there is a proper connection between the sensor board and main
board.Checkfordamagetothemainboardpinsnearthetipofthe
foregrip.
Trigger may need to be adjusted. Thetriggerindicationaarowtakesplaceofthetournamentlock
symbolt when the trigger is activated. If the trigger is being pressed
the aarow will point down, and point up if the trigger is released. If
it is not that way, then the trigger may need to be adjusted. See the
“TriggerAdjustments”sectionearlierinthemanual.Checkthatthere
is a proper connection between the sensor board and main board.
Checkfordamagetothemainboardpinsnearthetipoftheforegrip.
Solenoid may not be connected Removeairsourceandpaintballbeforedisassemblingthemarker.If
your remove the grip frame you should be able to verify the solenoid
is plugged into the Mini GS sensor board.
Multiplepaintballsredfromonlyoneshot Balldetentsmaybetornormissing Removetheeyecovertochecktheconditionoftheballdetents.If
damaged or bent permenantly replace one or both of them.
MarkerisBreakingpaintballsinthebreech Balldetentsmaybetornormissing Removetheeyecovertochecktheconditionoftheballdetents.If
damaged or bent permenantly replace one or both of them.
Eyes may be dirty Clean the eyes as described earlier in the manual. If the eyes are
dirtytheeyesymbolonthescreenwithhaveabigXinthemiddle
afterthemarkerisred.
Bolttipmaybebad Abadbolttipmayallowairtoesacpeupthefeedneckcausing
breakage.Thissymptomiscommonlyknownas“Blowback”
BoltguideorBolto-ringsmaybebad Badboltorsmallboltguideo-ringsmayallowairtoesacpeupthe
feedneckcausingbreakage.Thissymptomiscommonlyknown
as“Blowback”.Makesuretheseo-ringareingoodconditionand
properly lubricated. Replace if necessary.
MarkerisshootingslowerthansetROF Eyes may be dirty WhentheeyesaredirtytheROFislimitedto8bpstoprevent
excessiveballbreakage.Cleantheeyesasdescribedearlierinthe
manual. If the eyes are dirty the eye symbol on the screen with have
abigXinthemiddleafterthemarkerisred.
VelocityisLow/Inconsistentorvelocitydropsduringrapidre Poppeto-ringmaybedamagedornotproperlylubricated See general maintenance section earlier in the manual to see how to
properlycheckandlubricatepoppeto-ring.
BoltguideorBolto-ringsmaybebad/maynotbelubricated Boltshouldstayonboltguidewhenturnedboltsidedownandshak-
en.Ifboltfallsoffreplace3smallboltguideo-rings.Checkboltand
boltguideo-ringsfordamage.Assuretheseo-ringsareproperly
lubricated according to general maintenace section of this manual.
7. Troubleshooting