Manual

13
Possible issue with marker pressure Pressureshouldbesettoaround200psi.Ifpressuredropsduring
rapidreanddoesn’trecovertosetpressurebetweeneachshot
tryscrewingintankallthewayortryadifferenttank.Ifswitching
tankdoesn’thelptheregulator/ASAmayneedtobeserviced.See
Regulator maintenance guide in the manual
Velocityofrstshotishigherthanrestofstring Possible issue with marker pressure Pressureshouldbesettoaround200psi.Ifpressurerisesaboveset
pressurequicklyafterashottheregulatormayneedservice.See
Regulator Maintenance Guide in this manual.
Solenoiddoesn’tclick Batterymaynotbefresh TryanewbatteryandmakesurehighqualityAlkaline9Vbattery.
Solenoidmaybedirtyandissticking See solenoid cleaning in the maintenace section earlier in the man-
ual.
Markercontnuestorewhentriggerisnotbeingpulled Triggermaybeadjustedtooshort If trigger is adjusted too short it could cause undesired activations on
the switch. See Trigger adjustments section earlier in the manual to
make trigger longer.
Triggerde-bouncemayneedtobeincreased The circuit board hassettings called pull de-bounce and release de-
bounce that prevent accitential trigger swtch activations. Increaseing
thesesettingsmayxthisissue.SeeBoardsettingsandFunctions
section earlier in the manual to see how to adjust this.
Large gushing leak out of barrel/breech Solenoidmayneedtobereset Thesolenoidmayoccasionallystickopenfrombeingdirty,exces-
sive shock or loss of power in which case it needs to be reset. To
resetsolenoidremoveairsourceturnmarkeron,turntheeyesoff
pressingandholdifupdirection,presstriggermultipletimesyou
shouldhearsolenoidclicking.Ifsolenoiddoesn’tclicksee“Solenoid
doesn’tclick”sectionintroubleshootingguide.
Small leak down the barrel Thepoppetsealmaybedirtyordamaged Trycleaningpoppetsealandboltguideareawithaq-tip.Ifthis
doesn’tworkyoucanchangethesealontheendofthepoppet
bycarefullyunscrewingitwithplyersorreplacingtheentirepoppet
assembly.Damagemaynotbedetectablebytheeye.
Theboltguideisdirtyordamaged Trycleaningpoppetsealandboltguideareawithaq-tip.Ifthis
doesn’tworkyourboltguidemaybedamagedwherethepoppet
seals and therfore needs to be replaced.
Front large bolt guide 0-ring is damaged Replace o-ring
Constant leak inside grip frame Multiple causes Multiple seals or parts could cause a leak inside grip frame. Check
andreplacesealsifnecessaryforeachpossiblecause.Possible
causes include: Solenoid Gasget, Solenoid, Large bolt guide o-rings,
O-rings on air transfer tubes,
Leakfrombackcap/velocityadjuster Velocityadjustercouldbeunscrewedtoofar ScrewVelocityadjusterbackin.
O-ringonVelocityadjustermaybedamaged Replacevelcityadjustero-ring.
Leak between bottom grip frame and regulator/asa ASAscrewmaybelose Remove either side of rear grip panel and tighten screw if it is loose
Airtransfero-ringmaybedamaged Change bottom air transfer o-ring.
Leak from bottm of regulator ASA where lever is Multiple causes Thesetwoo-ringmaycausethisissue(72509,72399)-seeregula-
tor maintenance guide on how to access these o-rings
Leakfromsilvercapwith4holesonregulator Regulator pressure is set too high This cap contains the over pressure protection valve (OPP valve).
Itwillleakitthepressureisapproximatley250psiorhigher.Ifit
leaksatlessthan200psiitmayneedservicewhichwouldrequirea
certiedtech.