Manual

8
TPS.Oncedone,theLEDwillcyclethroughanarrayofcolorstoindicatethesettingissavedand
return to the Settings Mode.
Note: This setting affects only Millennium/ Ramp Firing Mode.
FACTORY RESET
Theboardhasafeaturethatallowstheusertoresetallofthesettingsbacktothestockconguration.
Tournament Lock must be off to perform factory reset. The following steps are required to perform a
FactoryReset:
1. WithboardOff,turnmarkerOninsettingsmode.
2. PressandholdthebuttonontheForegrip,thenpressandholdtheTriggersothatboththebutton
 andTriggerarebeingheldsimultaneously(Note:buttonmustbepressedrst).
3. HoldboththebuttonandTriggerforapproximately5-6seconds.TheLEDwillthenstartalternating
green and red. Now release the button and Trigger.
4. Whentheboardisdoneresettingtheboardwillturnoff.
TRIGGER ADJUSTMENT
Thereareveadjustmentsthatcanbemadeontheonthetrigger(Fig6-2).Usethe5/64”hexwrench
tomakeanydesiredadjustments:
A. Forward Travel – This adjusts the position of the trigger
whennotbeingred
- Turning the adjustment screws “in” or clockwise will
decrease the trigger length of travel
B. Stop – This adjusts the farthest position the trigger will
travel when depressed
- Turning the adjustment screws “in” or clockwise will
decrease the travel of the trigger by having the trigger stop
sooner
C. Activation Point – This adjusts the position where the
trigger pull registers a shot by activating the trigger switch
- Turning the adjustment screws “in” or clockwise will decrease
the travel of the trigger needed before the AXE registers a shot
D. Magnetic Tension – This affects how “hard” the pull of the trigger is
- Turning the adjustment screws “in” or clockwise will increase the force needed to pull the trigger
7. ASSEMBLY/DISASSEMBLY AND MAINTENANCE
CAUTION: Before attempting to perform any maintenance operations or any marker disassembly,
make sure that all paintballs and propellant sources have been removed from the marker and that the
Regulator gauge reads 0 psi. Install a barrel blocking device, and that the power is Off.
GENERAL MAINTENANCE
KeepyourAXEcleanandlubricatedtoeliminatethefrictionthatwouldpreventreliableoperation.Clean
and lube the marker before each use, and do not put it away dirty. Only use oils designed for paintball
andtheymayonlybeusedontheregulator.DONOTUSEOILONTHEBOLTSYSTEM.DoNOTuse
petroleum-basedlubricantsinthelubricationofthismarker.Underanycircumstances,doNOTusea
solvent-basedlubricant.Teonorsilicone(Non-sprayonly)lubricantsdesignedforuseonO-ringsmay
beusedforlubricationfortheboltareaonlyofthemainhousing.OnlyusePaintballspecicmarker
grease,suchasEmpireVitaminEgrease.Thefollowingmaintenanceproceduresdescribedbelow
shouldbeperformedbeforeeachdayofuseorevery20,000shots,whichevercomesrst.
REMOVAL, INSTALLATION AND CLEANING
OF BALL DETENTS AND EYES
− Usinga5/64”hexwrench,inserthex
wrench into the screw hole of the Eye
 Coverandturncounter-clockwise.(Fig7-1)
− Usingtheendofthehexwrench,carefullyprytheBallDetentfromtheBody
− Cleanthedetentwithadampclothorwithwarmwaterifcoveredwithpaint
− PlacetheDetentbackintoitssocketwithintheBody
− Usingtheendofthehexwrench,carefullyprytheEyefromtheBodyusingcarenottodamagethe
eye wires
− CleantheEyewithadrycloth
− CarefullyreplacetheEyeintothesocketintheBody
− InstalltheEyeCovermakingsuretheEyeissafelyinitssocket.Tightenthescrewwitha5/64”hex
wrench.
Note: Be careful not to lose the detents as they are small and unattached.
REMOVAL OF BOLT AND BOLT GUIDE
ASSEMBLY
− PressandholdtheBoltGuideRelease
 Button,locatedontheleft-sideofthe
 rearoftheGripFrame(Fig7-2)
− Whileholdingthebutton,gripandpullthe
 BoltGuidefreeoftheBodyremovingthe
 boltsystem(Fig7-3)
MAINTENANCE OF BOLT AND BOLT GUIDE ASSEMBLY
- InspecttheO-ringsonboththeboltandBoltGuideforanywearordamage.Replacedamagedor 
 wornO-ringsifnecessary.(Fig7-4)
- LubricateallO-ringsonBoltandBoltGuidewithEmpiremarkergrease,thesuppliedgreaseora 
 paintballspecicmarkergrease.Onlyasmallamountisneeded.
(FIG. 6-2)
(FIG. 7-2)
(FIG. 7-3)
(FIG. 7-1)
(FIG. 7-4)