Manual

6
SETTINGS MODE
The AXE must be Off and the Tournament Lock must be Off to begin managing the settings and
functions. To activate the marker in Settings Mode, press and hold the Trigger, then press and hold
the button on the back side of the Foregrip. The LED will cycle through an array of colors to indicate
theSettingsmodeisactive.YoumaynowreleasetheTriggerandthebutton.OncetheLEDisdone
cycling you are ready to navigate through settings mode.
NAVIGATING THROUGH SETTINGS
Once in Settings Mode, use the Trigger is used to navigate to the next setting, where the LED
indicateswhichsettingaslistedinthechartbelow.PressingandreleasingtheTriggerquicklywill
navigate to the next setting.
The LED color/status will change accordingly.
Example:IfcurrentlyinFiringMode(solidRed),pressandreleasetheTrigger3timestogetto
De-Bounce(ashingRed).
CHANGING SETTINGS
Tochangeasetting,rstnavigatetothesettingyouwouldliketochangebyusingtheTriggeras
describedabove.Onceatthedesiredfunction,pressandholdtheTriggerfor2seconds.TheLEDwill
thenbeginblinkingtoindicatethesetting’scurrentvalue.Oncetheblinkingstops,theMLEDwillturn
offandyouhavea3secondwindowtobeginenteringanewvalue.PressandreleasetheTriggerthe
number of times corresponding to the desired new setting value. After the desired number is reached,
release the Trigger and after 3 seconds the LED will cycle through an array of colors to indicate the
settingissaved.IfyoudonotenteranyTriggerpullstomodifyasetting,thevalueremainsthesame.
IfyouentermorethanmaximumamountofTriggerpullsforanysetting,thevaluewillbecomethe
maximumvalueforthatsetting.PoweroffthemarkertoexittheSettingsMode.Anysettingthatwas
modiedwillbestoredandreadytouseuponstartup.
FIRING MODES
IndicatedbyaSolidRedLED
YoumustbeintheSettingsModetochangeFiringModes,seeaboveforinstructionsonhowtoenter
SettingsMode.AfterchoosingFiringModes(SolidRed),holdtheTrigger,theLEDwillashRedLED
blinksequaltothecurrentsetting,followedbyapause.PulltheTriggerthenumberoftimesequalto
yournewdesiredsetting(seechartbelow).Oncedone,theLEDwillcyclethroughanarrayofcolors
toindicatethesettingissavedandreturntotheSettingsMode.Thereare4ringmodesavailable:
SemiAuto,Burst,Ramp,andFullAuto.
Note: All modes will perform 3 semi-auto safety shots prior to the activation of the mode, as required by ASTM.
IMPORTANT: When the Firing Mode is changed it will also automatically modify the
corresponding Max Rate of Fire and ramping parameters that correspond to that mode. These
settings may be changed after Firing Mode is selected
SemiAuto:Markerwillshoot1timeforeachtimetheTriggerispulled.
 Default:MaxROF=15.0bps
Burst:Markerwillshootinsemi-automodeequaltothenumberofshotsspeciedbytheRampStart
setting(seebelowformoreinformation),thenwillgointoa3-shotburstattheMaxROFsetting.Ifthe
markerisnotredfor1second,themarkerwillshootsemi-autountilRampStart
is again achieved.
 Default:MaxROF=12.0bps;RampStart=3shots
Ramping:Markerwillshootinsemi-automodeequaltothenumberofshotsspeciedbytheRamp
Startsetting,andiftheRampSustainROF(seebelowformoreinformation)isachieved,themarker
willrampuptotheMaxROFsetting.Ifthemarkerisnotredfor1second,themarkerwillshootsemi-
auto until ramping parameters are achieved.
 Default:MaxROF=10.0bps;RampStart=3shots;RampSustain=6tps(Triggerpullspersecond)
FullAuto:Markerwillshootinsemi-automodeequaltothenumberofshotsspeciedbytheRamp
Startsetting,thenwillgointofullautomaticmodeaslongastheTriggerishelddown.Ifthemarkeris
notredfor1second,themarkerwillthenshootsemi-autoagainuntilRampStart
is achieved again.
 Default:MaxROF=12.0bps;RampStart=3shots
MAX RATE OF FIRE (ROF)
-INDICATEDBYSOLIDGREENLED
Thissettingcontrolsthemaximumnumberofpaintballpersecondthemarkerisallowedtore.The
settingcanbevariedfrom8to20ballspersecond(bps)in0.5bpsintervals.Usethechartbelowto
set the Max ROF.
 Default:MaxROF=15.0bps
YoumustbeintheSettingsModetochangetheMaxROF,seeaboveforinstructionsonhowto
enterSettingsMode.AfterchoosingMaxROFMode(SolidGreen),holdtheTriggertogetintothe
Mode,theLEDwillashGREENLEDblinksequaltothecurrentsetting,followedbyapause.Pullthe
Triggerthenumberoftimesequaltoyournewdesiredsetting(seechartbelow).Oncedone,theLED
will cycle through an array of colors to indicate the setting is saved and return to the Settings Mode.
LED COLOR SETTING
SOLID REDFIRING MODE
SOLID GREEN MAX ROF
SOLID AMBERDWELL
SOLID REDDE-BOUNCE
SOLID GREEN BALL IN PLACE
SOLID AMBERRAMP START
FAST FLASHING REDRAMP SUSTAIN
NUMBER
OF BLINKS
MODE
1SEMI-AUTO
2B
URST
3RAMPING
4FULL AUTO