Manual

14
VelocityisLow/Inconsistentorvelocitydropsduringrapidre PoppetO-ringmaybedamagedornotproperlylubricated See general maintenance section earlier in the manual to see how to
properly check and lubricate poppet O-ring.
BoltguideorBoltO-ringsmaybebad/maynotbelubricated Boltshouldstayonboltguidewhenturnedboltsidedownandshak-
en.Ifboltfallsoffreplace3smallboltguideO-rings.Checkboltand
bolt guide O-rings for damage. Assure these O-rings are properly
lubricated according to general maintenance section of this manual.
Possibleissuewithmarkerpressure Pressureshouldbesettoaround200psi.Ifpressuredropsduring
rapidreanddoesn’trecovertosetpressurebetweeneachshot
tryscrewingintankallthewayortryadifferenttank.Ifswitching
tank doesn't help the regulator/ASA may need to be serviced. See
Regulator maintenance guide in the manual
Velocityofrstshotishigherthanrestofstring Possibleissuewithmarkerpressure Pressureshouldbesettoaround200psi.Ifpressurerisesaboveset
pressure quickly after a shot the regulator may need service. See
RegulatorMaintenanceGuideinthismanual.
Markercontnuestorewhentriggerisnotbeingpulled Trigger may be adjusted too short Iftriggerisadjustedtooshortitcouldcauseundesiredactivationson
the switch. See Trigger adjustments section earlier in the manual to
make trigger longer.
Solenoiddoesn’tclick Batterymaynotbefresh TryanewbatteryandmakesurehighqualityAlkaline9Vbattery.
Solenoid may be dirty and is sticking See solenoid cleaning in the maintenance section earlier in the manual.
Markercontinuestorewhentriggerisnotbeingpulled Trigger may be adjusted too short Iftriggerisadjustedtooshortitcouldcauseundesiredactivationson
the switch. See Trigger adjustments section earlier in the manual to
make trigger longer.
Trigger de-bounce may need to be increased The circuit board has settings called pull de-bounce and release
de-bouncethatpreventaccidentaltriggerswatchactivations.In-
creasingthesesettingsmayxthisissue.SeeBoardsettingsand
Functions section earlier in the manual to see how to adjust this.
Large gushing leak out of barrel/breech Solenoid may need to be reset The solenoid may occasionally stick open from being dirty, exces-
sive shock or loss of power in which case it needs to be reset. To
reset solenoid remove air source turn marker on, turn the eyes off
pressing and hold if up direction, press trigger multiple times you
shouldhearsolenoidclicking.Ifsolenoiddoesn'tclicksee"Solenoid
doesn't click" section in troubleshooting guide.
Small leak down the barrel The poppet seal may be dirty or damaged The poppet seal may be dirty or damaged
The bolt guide is dirty or damaged ScrewVTrycleaningpoppetsealandboltguideareawithatip.If
thisdoesn’tworkyourboltguidemaybedamagedwherethepoppet
seals and therefore needs to be replaced.
Front large bolt guide 0-ring is damaged Replace O-ring
Constantleakinsidegripframe Eyes may be dirty Multiple causes Multiplesealsorpartscouldcausealeakinsidegripframe.Check
andreplacesealsifnecessaryforeachpossiblecause.Possible
causesinclude:SolenoidGasket,Solenoid,LargeboltguideO-rings,
O-rings on air transfer tubes,
Leak from back cap/velocity adjuster Velocityadjustercouldbeunscrewedtoofar ScrewVelocityadjusterbackin.
Air transfer O-ring may be damaged ChangebottomairtransferO-ring.
Leak from bottom of regulator ASA where lever is Regulator pressure is set too high Thiscapcontainstheoverpressureprotectionvalve(OPPvalve).
Itwillleakitthepressureisapproximately250psiorhigher.Ifit
leaksatlessthan200psiitmayneedservicewhichwouldrequirea
certiedtech.