Manual

13
Marker does not turn On Batterymaynotbefresh Ifyouhavetriedseveraldifferentbatteries,checktomakesurethe
batteryharnessispluggedintotheboardproperly.Ifitis,unplugthe
batteryfromtheharness,pressandholdthepowerbuttonfor15sec
thenrelease.Plugthebatterybackinandtryagain.
Boardmayhavemoisturedamage The circuit board is protected with a moisture resistant coating but
occasionally prolonged exposure to moisture can cause a malfunc-
tion.Ifthemarkerwasusedinwetconditionsunplugthebattery
and remove both circuit board from marker to allow them to dry for at
least24hoursthentryturningitonagain.
Markerdoesnotre/cycle Marker may not be turned on Checkscreenonrearofforegrip.OLEDscreenshouldbeonwhen
marker is turned on.
Paintballsmaynotbefedintobreech Theanti-chopeyesystempreventsthemarkerfromringunlessa
ballispresent.Whentheeyesdetectaballtheeyesymbolonthe
screenwillhavealledcircleinthemiddle.Neverputanything
otherthanapaintballdownthefeedneckoftheAXE.Checkthatthe
bolt is fully returning and if not service you may need to change bolt
tip,smallboltguideO-ringsand/ortheboltO-rings.Checkthatthere
is a proper connection between the sensor board and main board.
Checkfordamagetothemainboardpinsnearthetipoftheforegrip.
Trigger may need to be adjusted. The trigger indication arrow takes place of the tournament lock
symbolwhenthetriggerisactivated.Ifthetriggerisbeingpressed
thearrowwillpointdown,andpointupifthetriggerisreleased.If
it is not that way, then the trigger may need to be adjusted. See the
“TriggerAdjustments”sectionearlierinthemanual.Checkthatthere
is a proper connection between the sensor board and main board.
Checkfordamagetothemainboardpinsnearthetipoftheforegrip.
Solenoid may not be connected Removeairsourceandpaintballbeforedisassemblingthemarker.If
your remove the grip frame you should be able to verify the solenoid
is plugged into the AXE sensor board.
Multiplepaintballsredfromonlyoneshot Balldetentsmaybetornormissing Removetheeyecovertochecktheconditionoftheballdetents.If
damaged or bent permanently replace one or both of them.
MarkerisBreakingpaintballsinthebreech Balldetentsmaybetornormissing Removetheeyecovertochecktheconditionoftheballdetents.If
damaged or bent permanently replace one or both of them.
Eyes may be dirty Cleantheeyesasdescribedearlierinthemanual.Iftheeyesare
dirty the eye symbol on the screen with have a big X in the middle
afterthemarkerisred.
Bolttipmaybebad A bad bolt tip may allow air to escape up the feedneck causing
breakage.Thissymptomiscommonlyknownas“Blowback”
BoltguideorBoltO-ringsmaybebad BadboltorsmallboltguideO-ringsmayallowairtoescapeupthe
feedneck causing breakage. This symptom is commonly known
as"Blowback".MakesuretheseO-ringareingoodconditionand
properly lubricated. Replace if necessary.
Marker is shooting slower than set ROF Eyes may be dirty WhentheeyesaredirtytheROFislimitedto8bpstoprevent
excessiveballbreakage.Cleantheeyesasdescribedearlierinthe
manual.Iftheeyesaredirtytheeyesymbolonthescreenwithhave
abigXinthemiddleafterthemarkerisred.
11. TROUBLESHOOTING GUIDE