Owner`s manual

ManualsBrandsEmpire Comfort Systems ManualsConsumer electronicsVFP36FB2CF-3

Page 1

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

DO NOT ATTEMPT TO MODIFY OR ALTER THE CONSTRUC-

TION OF THE FIREBOX OR ITS COMPONENTS. ANY MODI-

FICATION OR ALTERATION OF CONSTRUCTION MAY VOID

THE WARRANTY OF THIS FIREBOX.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE

HAZARDS OF HIGH SURFACE TEMPERATURE AND

SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IG-

NITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED

WHEN THEY ARE IN THE SAME ROOM AS THE FIREBOX.

FOR USE ONLY WITH A LISTED GAS-FIRED UNVENTED

DECORATIVE ROOM HEATER NOT TO EXCEED 40,000

BTU/H.

DO NOT BUILD A WOOD FIRE.

UNIVERSAL FIREBOX FOR ALL

VENT-FREE LOG SETS

MODELS

VFP32FB2DL-4 VFP36FB2DL-4 VFP42FB2DL-4

VFP32FB2CL-3 VFP36FB2CL-3 VFP42FB2CL-3

VFP32FB2EL-3 VFP36FB2EL-3 VFP42FB2EL-3

VFP32FB2DF-4 VFP36FB2DF-4 VFP42FB2DF-4

VFP32FB2CF-3 VFP36FB2CF-3 VFP42FB2CF-3

VFP32FB2EF-3 VFP36FB2EF-3 VFP42FB2EF-3

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause injury or property dam-

age. Refer to this manual. For assistance or additional infor-

mation, consult a qualied installer, service agency or the

gas supplier.

Carefully review the instructions supplied with the decora-

tive type unvented room heater for the minimum replace

size requirement.

DO NOT INSTALL A VENT-FREE LOG SET IN THIS FIREBOX,

UNLESS THIS FIREBOX MEETS THE MINIMUM DIMENSIONS

REQUIRED FOR THE INSTALLATION.

GAS-FIRED

ANSI Z21.91 Ventless Fireplace Enclosures for Gas

Fired Decorative Type Unvented Room Heaters

— Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appli-

ance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

WARNING: If the information in these instructions are

not followed exactly, a re or explosion may result caus-

ing property damage, personal injury or loss of life.

Installer: Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

EMPIRE

Comfor t Systems

Summary of content (24 pages)

PAGE 1
EMPIRE INSTALLATION Instructions AND Owner's Manual Comfort Systems UNIVERSAL FIREBOX FOR ALL VENT-FREE LOG SETS MODELS VFP32FB2DL-4 VFP36FB2DL-4 VFP42FB2DL-4 VFP32FB2CL-3 VFP36FB2CL-3 VFP42FB2CL-3 VFP32FB2EL-3 VFP36FB2EL-3 VFP42FB2EL-3 VFP32FB2DF-4 VFP36FB2DF-4 VFP42FB2DF-4 VFP32FB2CF-3 VFP36FB2CF-3 VFP42FB2CF-3 VFP32FB2EF-3 VFP36FB2EF-3 VFP42FB2EF-3 GAS-FIRED ANSI Z21.
PAGE 2
TABLE OF CONTENTS Section Page Important Safety Information.....................................................................................3 Introduction...............................................................................................................3 Clearances.............................................................................................................4-5 Firebox Installation Instructions..............................................................................
PAGE 3
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) and to the National electrical Code, ANSI/NFPA70 (latest edition). Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance. Provide adequate combustion and ventilation air. NOTE: Installation and repair should be done by a qualified service person.
PAGE 4
CLEARANCES Sidewall Clearances: The clearance from the inside of the firebox to perpendicular combustible side wall should not be less than 6". See Figure 1. COMBUSTIBLE FINISHED WALL OR MANTEL 2X4 HEADER Firebox Side and Back Clearances: The firebox outer casing side and back flanges are zero clearance to combustibles. Top Framing and Finishing: Combustible framing may rest on top of standoffs. Combustible finishing materials may extend to the top standoff screws on the front edge of the outer wrap.
PAGE 5
CLEARANCES Ceiling Clearances: The ceiling height should not be less than 42" from the top of the hood. See Figures 3a and 3b. Mantel Clearances: Vent free firebox models must use the hood supplied with the firebox, or one of the optional hood kits available for each model. If a combustible mantel is installed, it must meet the clearance requirements detailed below. Grate Clearance: The minimum clearance between the front legs of the grate and front edge of the firebox is 2".
PAGE 6
FIREBOX INSTALLATION INSTRUCTIONS Any vent-free Gas Log Heater must be “For use with approved ANSI Z21.11.2 unvented room heater.” has not been done, stop and consult your dealer for assistance with this planning. Follow and complete the installation instructions of the gas log set and the requirements of this firebox. Planning Your Installation Please note that the optional BVA1 Fresh Air kit available for use with the Vent Free Firebox must be installed at the time of the initial installation.
PAGE 7
FIREBOX INSTALLATION INSTRUCTIONS (continued) C PREMIUM LOUVERED E G I A PREMIUM FLUSH E G I A J H F B F B H K D L M PREMIUM LOUVERED FLUSH VFP32 VFP36 VFP42 VFP32 VFP36 VFP42 A 41 1/8” 41 1/8” 41 1/8” 41 1/8” 41 1/8” 41 1/8” B 34 1/2” 39 1/2” 43 1/2” 34 1/2” 39 1/2” 43 1/2” C 21 7/16” 21 7/16” 21 7/16” 21 7/16” 21 7/16” 21 7/16” D 27 1/4” 32 1/4” 36 1/4” 27 1/4” 32 1/4” 36 1/4” E 38 1/2” 38 1/2” 38 1/2” 38 1/2” 38 1/2” 38 1/2” F 31” 36” 40” 31”
PAGE 8
FIREBOX INSTALLATION INSTRUCTIONS (continued) Locating Firebox Place firebox in framing opening. Use the four (4) framing brackets provided on the firebox to attach firebox to framing. Different hole locations can be used for finishing materials with thicknesses of 3/8", 1/2" and 3/4". Attach these materials with screws provided, two (2) per framing bracket. See Figure 8. Framing brackets should fit directly against framing material. Use at least one (1) nail per bracket to secure in place.
PAGE 9
INSTALLING HOOD (continued) Extended Hoods If your non-combustible facing material is over 1" in thickness that will be used to finish this firebox, an extended hood is available that will extend out 2" farther out into the room. Contact your local dealer for details.
PAGE 10
OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS FOR DELUXE AND PREMIUM FIREBOXES The optional BVA1 Fresh Air Kit is designed to introduce outside air to the fireplace or firebox as desired. It must be installed prior to, or at the time of fireplace or firebox installation to framing. The Fresh Air kit must be installed prior to the installation of wallboard or other finishing materials around the unit.
PAGE 11
DAMPER ASSEMBLY OUTSIDE AIR ROD BRACKET OUTER CASING OPEN FRESH AIR ROD OUTSIDE AIR ROD BRACKET TOP CUTAWAY VIEW Figure 18 FRESH AIR ROD (CONTROL LEVER) DAMPER ASSEMBLY LEFT SIDE VIEW OF FIREBOX OUTSIDE OPENINGAIR ROD BRACKET Figure 21 OUTER CASING FRESH AIR ROD OPEN TOP CUTAWAY VIEW OUTSIDE AIR ROD BRACKET FRESH AIR ROD (CONTROL LEVER) 1 Figure 19 7.
PAGE 12
OUTSIDE PLATE/VENT SCREEN ASSEMBLY AIR DOOR ASSEMBLY OUTSIDE HOOD 4” DIA. AIR DUCT CONNECTOR (INSTALLER SUPPLIED) FIREBOX OR FIREPLACE Figure 22 Completion of Air Kit installation 1. Determine the length of 4” Dia. rigid or flex duct connector (installer supplied) you will need from the firebox/fireplace to the exterior surface of the outside wall, where the air kit hood will be installed.
PAGE 13
OPTIONAL SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS Attention: Install blower assembly before connecting gas inlet supply line. Wiring The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, if an external electrical source is utilized.
PAGE 14
4. Insert blower assembly into interior, bottom of firebox. Position blower assembly so that you align the notch on back of blower assembly with the center screw on firebox back, then push the blower assembly against firebox back. The blower wheel must be centered with the back wall of the firebox. The magnets on the back and bottom of blower assembly will sufficiently hold blower assembly in place.
PAGE 15
Blower Motor The blower motor does not have oiling holes. Do not attempt to oil the blower motor. JUNCTION BOX 110 VOLT AC FAN/MOTOR ASSEMBLY Blower Wheels The blower wheels will collect lint and could require periodic cleaning. If the air output decreases or the noise level increases, it indicates a dirty blower wheel. Remove fan and clean blower wheels. Warning: Unplugging of blower accessory will not stop the heater from cycling.
PAGE 16
JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED.
PAGE 17
PARTS LIST PART NUMBER INDEX NO.
PAGE 18
PARTS LIST PART NUMBER INDEX NO.
PAGE 19
PARTS VIEW 1 1 2 3 16 17 17 13 4 7 6 14 5 15 8 12 11 10 9 27061-2-0711 21 18 20 19 Page 19
PAGE 20
ACCESSORIES Accessory Description Fan Kit Model Numbers 2 1 Designed to provide forced air flow.
PAGE 21
ACCESSORIES (continued) Extended 4" Hoods Extended hoods that extend out 2" farther than the standard hoods, to accommodate thicker surround materials. Available as optional kits in Black, Brass, Hammered Pewter, and Stainless Steel finishes. Contact dealer for all available optional hood accessories Louvers Styles include Slat, Mission, Arch, and Leaf Patterns. Available as optional kits in Black, Brass, Hammered Pewter, and Stainless Steel finishes.
PAGE 22
MASTER PARTS DISTRIBUTOR LIST To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort. com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time.
PAGE 23
APPLIANCE SERVICE HISTORY Date Dealer Name 27061-2-0711 Service Technician Name Service Performed/Notes Page 23
PAGE 24
EMPIRE Comfort Systems Empire Comfort Systems Inc. 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. www.empirecomfort.