Instructions

ManualsBrandsEmko ManualsAutomationBang-bang, P, PI, PD, PID Temperature controller Pt100, J, K, R, S -200 up to 170

: Process �nput type select�on parameter. (Default: )

J type (Fe,Cu,N�) Thermocouple; -200ºC,900ºC ; -328ºF,1652ºF

J type (Fe,Cu,N�) Thermocouple; -199.9ºC,900.0ºC ; -199.9ºF,999.9ºF

K type (N�,Cr,N�) Thermocouple; -200ºC,1300ºC ; -328ºF,2372ºF

K type (N�,Cr,N�) Thermocouple; -199.9ºC,999.9ºC ; -199.9ºF,999.9ºF

R type (Pt13%RhPt) Thermocouple; 0ºC,1700ºC ; 32ºF,3092ºF

R t�p� (Pt13%RhPt) Thermocouple; 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF

S t�p� (Pt10%RhPt) Thermocouple; 0ºC,1700ºC ; 32ºF,3092ºF

S t�p� (Pt10%RhPt) Thermocouple; 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF

PT100 Thermores�stance; -200ºC,650ºC ; -328ºF,1202ºF

PT100 Thermores�stance; -199.9ºC,650.0ºC ; -199.9ºF,999.9ºF

: Un�t select�on parameter. or can be chosen. (Default: )

: Operat�on scale m�n�mum(Low L�m�t) value. It changes accord�ng to

the process �nput type and scale. (Default: -200)

: Operat�on scale max�mum(H�gh L�m�t) value. It changes accord�ng to

the process �nput type and scale. (Default: 900)

: Process set value low l�m�t parameter. It can be adjusted between

Operat�on Scale M�n�mum( ) and Process Set Value H�gh L�m�t( ).

(Default:-200)

: Process set value h�gh l�m�t parameter. It can be adjusted between

Process Set Value Low L�m�t( ) and Operat�on Scale Max�mum( )

and (Default: 900)

: Process offset value. It can be adjusted as a degree( or ), from

-10% of scale to 10% of scale.It �s added to the process value. (Default: 0)

: Output control type parameter. It can be selected or .

(Default: )

: Hysteres�s value. It can be adjusted from 1º(po�nt representat�on:

0.1º) to 20º. (Default: 3)

: M�n�mum ON/OFF control output t�me parameter. It can be adjusted

from 0 to 60 seconds. (SSR Default: 0 ; Relay Default: 5)

: Proport�onal band (P). It can be adjusted from %1.0 to %100.0.

(Default: 10.0)

: Output Control Per�od. If control output �s SSR, It can be adjusted

from 0.5 to 150.0 seconds. If control output �s Relay, It can be adjusted 60.0

to 150.0 seconds. (SSR Default: 10.0 ; Relay Default: 60.0)

: Proport�onal Offset value. Th�s parameter �s used for sh�ft�ng the

proport�onal band. It can be adjusted from (-Operat�on Scale Max�mum /2)

to (Operat�on Scale Max�mum /2). (Default: 0)

: Integral T�me. It can be adjusted from 0 to 3600 seconds.

(Default: 100)

: Der�vat�ve T�me. It can be adjusted from 0.0 to 999.9 seconds.

(Default: 25.0)

Bakım

Adjustment of Hysteres�s Value for ON/OFF Control

Time

Temperature

Set Value

Temperature

Control Output

Temperature

Hysteresis

In ON/OFF control algor�thm, temperature value �s tr�ed to keep equal to set

value by open�ng or clos�ng completely last control element. ON/OFF controlled

system, temperature value osc�llates cont�nuously. Temperature value’s

osc�llat�on per�od or ampl�tude around set value changes accord�ng to controlled

system. For reduc�ng osc�llat�on per�od of temperature value, a threshold zone

�s formed below or around set value and th�s zone �s named hysteres�s. Act�on

of control output �s descr�bed w�th f�gures below.

Temperature

Control Output

Temperature

Set Value

Temperature

ON/OFF

Conrol Form

with

Hysteresis

Other Informat�ons

Manufacturer Informat�on:

Emko Elektron�k Sanay� ve T�caret A.Ş.

Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369

BURSA/TURKEY

Phone : +90 224 261 1900

Fax : +90 224 261 1912

Repa�r and Ma�ntenance Serv�ce Informat�on:

Emko Elektron�k Sanay� ve T�caret A.Ş.

Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369

BURSA/TURKEY

Phone : +90 224 261 1900

Fax : +90 224 261 1912

Order�ng Informat�ons

Supply Voltage

Customer

24VV (±%15) 50/60Hz

115VV (±%15) 50/60Hz

230VV (±%15) 50/60Hz

Input Type

Conf�gurable20

Scale

See Parameters ( )

In package,

-One piece unit

-Two pieces mounting clamp

-One piece instruciton manual

A visual inspection of this product for possible damage occured

during shipment is recommended before installation. It is your

responsibility to ensure that qualiﬁed mechanical and electrical

technicians install this product.

If there is danger of serious accident resulting from a failure or

defect in this unit, power oﬀ the system and the electrical

connection of the device from the system.

The unit is normally supplied without a power switch or a fuse.

Use power switch and fuse as required.

Be sure to use the rated power supply voltage to protect the unit

against damage and to prevent failure.

Keep the power oﬀ until all of the wiring is completed so that

electric shock and trouble with the unit can be prevented.

Never attempt to disassemble, modify or repair this unit.

Tampering with the unit may results in malfunction, electric shock

or ﬁre.

Do not use the unit in combustible or explosive gaseous

atmospheres. During the equipment is put in hole on the metal

panel while mechanical installation some metal burrs can cause

injury on hands, you must be careful.

Montage of the product on a system must be done with it's

mounting clamp. Do not do the montage of the device with

inappropriate mounting clamp. Be sure that device will not fall

while doing the montage.

It is your responsibility if this equipment is used in a manner not

speciﬁed in this instruction manual.

Before beg�nn�ng �nstallat�on of th�s product, please read

the �nstruct�on manual and warn�ngs below carefully.

Installat�on

Warranty

EMKO Elektronik warrants that the equipment delivered is free from defects

in material and workmanship. This warranty is provided for a period of two

years. The warranty period starts from the delivery date.

This warranty is in force if duty and responsibilities which are

determined in warranty document and instruct on manual performs by the

customer completely.

Ma�ntenance

Repairs should only be performed by trained and specialized personnel. Cut

power to the device before accessing internal parts. Do not clean the case

with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of

these solvents can reduce the mechanical reliability of the device. Use a

cloth dampened in ethyl alcohol or water to clean the external plastic

case.

Before comm�ss�on�ng the dev�ce, parameters must be set �n

accordance w�th des�red use. Incomplete or �ncorrect conf�gurat�on

can cause dangerous st�uat�ons.

Because of l�m�ted mechan�cal l�fe of relay output contact, SSR output

�s recommended wh�ch the dev�ce use PID control algor�tm. The

dev�ce w�th ON/OFF control algor�tm, hysteres�s parameter must be

set a su�table value for your system, to avo�d too much relay sw�tch�ng.

V → Vac,

Z → Vdc,

W → Vdc or Vac can be appl�ed.

Output-1 (Temperature Control Output)

Relay Output (7A@250VV at Res�st�ve Load) (NO,NC,C)

SSR Dr�ver Output (Max. 10mA, 17VZ)

Output-2 (T�me Output)

Relay Output (5A@250VV at Res�st�ve Load) (NO,C)

SSR Dr�ver Output (Max. 10mA, 17VZ)

Output-3 (Steam Output) (ESM-9945-N)

Relay Output (5A@250VV at Res�st�ve Load) (NO,C)

SSR Dr�ver Output (Max. 10mA, 17VZ)

ESM-9945-N(96x96 DIN 1/4)

ESM-9944-N(96x96 DIN 1/4)

Access, Change and Record the Parameter Values

: If tune parameter �s set to or , dev�ce starts to calculate

PID parameters automat�cally. (Default: )

: Dev�ce does not calculate PID parameters.

: Step Response Tun�ng operat�on.

: L�m�t Cycle Tun�ng operat�on.

:Temperature - T�me d�splay form. If parameter value set as ,only

Temperature or T�me value �s d�splayed accord�ng to selected page. If

parameter value set as d�fferent from , Temperature and T�me value �s

d�splayed alternately dur�ng parameter value. It can be adjusted from

0 to 99 seconds. (Default: )

: T�mer d�splayed form. If parameter value set as , t�mer form �s

M�nute-Second. If parameter value set as , t�mer form �s Hour-M�nute.

(Default: )

: T�mer counts d�rect�on parameter. If the parameter set as , t�mer

counts downt-to-up. If the parameter set as , t�mer counts up-to-down.

(Default: )

: T�mer count�ng method parameter. If the parameter set as , t�mer

counts act�ve t�me. If the parameter set as , t�mer counts set t�me.

If parameter set as , th�s parameter �s not seen. (Default: )

: T�mer Relay Pos�t�on Parameter. If the parameter �s , T�mer relay

becomes act�ve pos�t�on w�th the t�me start and becomes pass�ve at the

end of the t�me. If the parameter �s , then t�me relay becomes act�ve at

the end of the t�me. (Default: )

: Relay act�ve t�me parameter. If parameter value set as then

T�me End Output w�ll be act�ve cont�nously. If value set as a d�fferent

value(from 1 to 9999 seconds), T�me End Output w�ll be act�ve dur�ng the

entered t�me. (Default: )

: Buzzer act�ve t�me parameter. If parameter value set as ,

Buzzer w�ll be act�ve cont�nously. If parameter value set as a d�fferent

value (from 1 to 9999 seconds), Buzzer w�ll be act�ve dur�ng the entered

t�me. (Default: )

: D�g�tal �nput c�rcu�t parameter. If the parameter set as , c�rcu�t �s

Normally Open (NO). If the parameter set as , c�rcu�t �s Normally Closed

(NC). (Default: )

: Type of command when d�g�tal �nput act�vated. If the parameter set

as , t�mer stops count�ng and resets t�me. If the parameter set as ,

t�mer pauses count�ng. (Default: )

: Steam durat�on parameter (ESM9945N). If the Steam Durat�on

Parameter �s selected as then the steam output w�l be on dur�ng the

Steam button �s pressed. If the parameter value set as a d�fferent value

(from 1 to 9999 seconds), after press�ng the steam button, output w�ll be

on dur�ng the Steam Durat�on Parameter value. If Steam button �s

pressed when steam output �s on, steam output w�ll be off. (Default: )

: Password for access�ng to the parameters sect�on. It can be

adjusted from 0 to 9999. If parameter value �s , password screen �s not

seen. If parameter value �s d�fferent from and ;

-If user enters d�fferent value from saved value, dev�ce w�ll return to

ma�n screen automat�cally.

-If user enters , all parameters can be observed except .

But dev�ce does not allow to do any changes �n parameters. (Default: )

Error Messages

Sensor fa�lure �n analog �nput. If there �s no

sensor connect�on or the value that �s read from

the analog �nput goes out of the dev�ce scale,

warn�ng �s observed.

ESM-9945-N

SET

°C

°F

+ -

ESD-9950-N

SET

°C

°F

+ -

Tune fa�lure. If �s selected �n PID Tune

Parameter( ) and start cond�t�ons are not

okay for Tune operat�on, the temperature value

�s d�splayed alternately w�th message on

d�splay dur�ng 10 seconds.

Parameters Descr�pt�ons

Start�ng the Tune operat�on

1- Enter the parameter and select or . Observe that bl�nks.

(If �s selected and start cond�t�ons are not okay for Tune operat�on,

bl�nks dur�ng 10 seconds.)

2- Dev�ce calculates PID control coeff�c�ents and sets the process value to

wanted value.

Cancell�ng tune operat�on:

1- If sensor breaks;

2-If tune operat�on can not be completed �n 8 hours;

3-Wh�le tune operat�on �s runn�ng, �f process value becomes greater than

process set value;

4-Wh�le tune operat�on �s runn�ng, �f user changes the process set value;

5-Wh�le tune operat�on �s runn�ng, �f user changes the parameter �n menu;

Then tune operat�on �s canceled and dev�ce cont�nues to run w�th former PID

parameters w�thout chang�ng PID parameters.

Tune Operat�on

SET

°C

°F

Parameter Values Screen

To increase parameter

value, turn encoder button

right. Press encoder button

to save.

SET

°C

°F

Parameter Values Screen

To decrease parameter

value, turn encoder button

left. Press encoder button

to save.

SET

°C

°F

Parameters Screen

SET

°C

°F

Parameters Screen

Turn encoder button

left to observe

previous parameter or

turn right to observe

next parameter.

Turn encoder button

left to observe

previous parameter or

turn right to observe

next parameter.

Note1: PID control parameters ( , , , , , ) are not seen when

output control type parameter ( ) �s set as .

Note2: ON/OFF control parameters ( , ) are not seen when output control type

parameter ( ) �s set as .

Note3: parameter �s not seen when parameter set as . parameter can be

seen after parameter.

Note4: parameter �s not seen �n ESM9944N dev�ce. parameter can be seen after

parameter.

Note5: If �s d�fferent from and user enters on password screen, parameter values

except are observed but can not be changed.

Note6: If no operat�on for 20 seconds on Parameters Screen, dev�ce automat�cally returns

Ma�n Screen .