User manual

ManualsBrandsEMKO ManualsElectronic Control SystemsTemperature controller 3 A relay, SSR (L x W x H) 65 x 76 x 35 mm

2.3 Panel Mounting and Removing

5. Changing and Saving Temperature and Humidity Set Value

5.1 Changing and Saving Humidity Set Value

Main Operating Screen

When SET button pressed ‘’S’’ led will

be active and temperature set value will

be displayed.

Temperature Set Value Screen

Temperature set value can

be changed with increment

and decrement buttons.

When SET button pressed

temperature set value can be saved.

Goes Humidity SET

value screen.

Temperature set value parameter ( Default =50 )

Temperature set value, can be programmed between minimum temperature set value and

maximum temperature set value .

°C

When SET button pressed

set value can be saved.

Humidity

Goes back to main operation screen.

Main Operating Screen

Humidity Set Value Screen

If no operation is performed in Humidity set value changing mode and temperature set value

changing mode for 20 seconds, device turns to main operation screen automatically.

Humidity Set Value Screen

5.1 Programming Mode Parameter List

In ON/OFF control algorithm, temperature

value is tried to keep equal to set value by

opening or closing the last control element.

ON/OFF controlled system, temperature

value oscillates continuously. Temperature

value’s oscillation period or amplitude

around set value changes according to

controlled system. For reducing oscillation

period of temperature value, a threshold

zone is formed below or around set value

and this zone is named hysteresis.

Temperature Sensor Offset Parameter ( Default = 0 )

3.2 Device Label and Connection Diagram

3. Electrical Wiring Diagram

3.1 Supply Voltage Input Connection of the Device

4.Front Panel Definition and Accessing to the Menus

7 8

9 10

Decimal Seperator Enabling Parameter ( Default = 0 )

None.

Only Temperature parameters with decimal seperator.

BUTTON DEFINITIONS

1. Increment Button :

** In main operation screen, press this button to change display temperature and humidity sensor

value.

** It is used to increase the value in the Temperature and Humidity Set screens and Programming mode.

2. Decrement, Silencing Buzzer Button :

** It is used to decrease the value in the Set screen and Programming mode.

** It is used to silence the buzzer.

3. Set Button:

** In the main operation screen; if this button pressed for the first time, Temperature set value will be

displayed. Value can be changed using increment and decrement buttons. When Enter button is

pressed again, value is saved and Humidty set value will be displayed next. Value can be changed using

increment and decrement buttons. When Enter button pressed again, value is saved and returns back

to main operating screen.

4.Enter Button:

** To access the programming screen; in the main operation screen, press and hold this button for 5

seconds.

** It is used to save value in the Set screens (Temperature or Humidity) and programming screen.

5.A1 led :

6. O1 Led :

** This led indicates that heating output is active.

7.Celcius led :

** Indicates that device is in C mode.

8.Fahrenheit led :

** Indicates that device is in F mode.

9. O2 Led :

** This led indicates that output is active.

10.A2 Led :

** This led indicates that Alarm is active.

11.Precent Sign ledi :

output is active

12.Program led :

** Indicates that device is in programming mode .

LED DEFINITIONS

It is active when Temperature alarm statuses.

Humidifier

** Indicates that device is in Humidity Set screen or Humidifier .

Temperature Unit Selection Parameter ( Default = 0 )

°C selected.

°F selected.

230VV CONNECTION DIAGRAM

Only Humidity parameters with decimal seperator.

Only Temperature and Humidity parameters with decimal seperator.

Temperature Control Selection Parameter On/Off or PID ( Default = 0 )

On - Off selected.

PID selected.

PID - Proportional Control Parameter ( Default =50 )

This parameter value can be adjusted form 0 to 100.

PID - Integral Parameter( Default = 1000 )

This parameter value can be adjusted form 0 to 3600.

PID - Derivative Parameter ( Default = 250 )

This parameter value can be adjusted form 0 to 3600.

PID -Period Time Parameter ( Default = 1 )

This parameter value can be adjusted form 1 to 50 second.

Humidity Sensor Scale Selection Parameter ( Default = 0 )

Buzzer Function Selection Parameter( Default = 0 )

Button Protection Parameter ( Default = 0 )

Programming Mode Accessing Password

It is used for accessing to programming mode. It can be adjusted from 0 to 9999. If it is 0,

password is not entered for accessing to the parameters. When the password screen is not

set as “12” , If the user enters ‘12’ in password screen and parameters are

accessed and they can changed.

( Default = 0 )

Humidity Alarm Function Selection Parameter ( Default = 0 )

Humidity (Default = 0)

When power is first applied to the device, this time delay must be expired for activation of

Humidity alarm.

Alarm Delay After Power On Parameter

It can be adjusted from 0 to 99 minutes.

Humidity Set Maximum Parameter(Default =Maximum Value of Device Scale)

if humidity alarm is active, this parameter value can be adjusted from humidity alarm set

minimum parameter to maximum value of the device scale.

Alarm

Humidity (Default = 0)

Humidity

Alarm On Delay Time Parameter

Alarm On Delay Time can be defined with this parameter. It can be adjusted

from 0 to 99 minutes.

Buzzer is inactive.

Buzzer is active during temperature alarm

Buzzer is active during humidity alarm

Buzzer is active during Temperature sensor failures.

Buzzer is active during Humidity sensor failures.

Buzzer is active during Temperature sensor failures or temperature alarm.

Buzzer is active during Humidity sensor failures or Humidity alarm.

Buzzer is active during Temperature sensor failures or Humidity sensor failures

or temperature alarm or humidity alarm.

There is no protection.

Temperature set value can not be changed.

Humidity set value can not be changed.

Temperature set value and Humidity set value can not be changed

Nem Set Parametresi (Default = 60%)

Humidity set value, can be programmed between minimum Humidity set value and maximum

temperature set value .

1-Before mounting the device in your panel, make

sure that the cut-out is of the right size.

2-Insert the device through the cut-out. If the

mounting clamps are on the unit, put out them

before inserting the unit to the panel.

3- Insert the mounting clamps to the fixing sockets

that located left and right sides of device and

make the unit completely immobile within the

panel

1-Pull mounting clamps from left and right

fixing sockets.

2-Pull the unit through the front side of the

panel

Before starting to remove the unit

from panel, power off the unit and

the related system.

Make sure that the power supply voltage is the same indicated on

the instrument.

Switch on the power supply only after that all the electrical

connections have been completed.

Supply voltage range must be determined in order. While installing

the unit, supply voltage range must be controlled and appropriate

supply voltage must be applied to the unit.

There is no power supply switch on the device. So a power supply

switch must be added to the supply voltage input.

Power switch must be two poled for seperating phase and neutral,

On/Off condition of power supply switch is very important in

electrical connection.

External fuse that on Vpower supply inputs must be on phase

connection.

External fuse that on Z power supply inputs must be on (+)

connection.

Power Supply Input

External

Fuse

(1A T)

Note-1

Supply

Switch

Supply Voltage

230V ( %15) 50/60Hz ,

115V ( %15) 50/60Hz ,

24V ( %15)50/60Hz ,

24V ( %15) 50/60Hz ,

V ±

W ±

10...30 V 1.5 W

Must be determined in order.

OFF

Temperature

Control

Output

Set

thSt

Time

thSt

Time

Temperature Set Value Screen

Humidity Set Value Screen

Humidity set value can be

changed with increment

and decrement buttons.

Relay Outputs

3 54 6 87 9 10

P/N : ESM-3723

Power Supply Voltage

230V ( %15) 50/60Hz ,

115V ( %15) 50/60Hz,

24V ( %15) 50/60Hz ,

V ±

W ±

10...30 V 1.5 W

11 12

Temperature Sensor Input

NTC, PTC, PT-100, 0/2..10V, 0/4..20mA

or ProNem Mini PMI-P

Humidity Sensor Input

0/2..10V, 0/4..20mA or

ProNem Mini PMI-P

Must be determined in order.

3x3A@ 250V V

5A @250VV

230 VV ± 15%

50/60Hz - 1.5VA

6 11 12

14A T Fuse

3x3A@ 250V V

5A @250VV

230 VV ± 15%

50/60Hz - 1.5VA

6 11 12

14A T Fuse

PTC Temperature and 0/4..20mA Humidity Sensor Input connection

VCC

GND

SCL

SDA

ProNem Mini PMI-P Temperature and Humidity Sensor Input Connection

Note: If this parameter is select 0, PID parameters ( , , , , ) will be not observed.

If this parameter select 1, parameter will be not observed.

Auto Tune (Limit Cycle Tuning) Selection Parameter ( Default = )

Device does not do(Limit cycle Tuning) operation.

Device does operation.

Hysteresis Parameter for Temperature ( Default = 0.1 °C )

From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C)

From 1 to 18°F for NTC,PTC ,PT-100 (32°F, 212°F)

From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C)

From 0.1 to 18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F)

From 1 to 10°C for ProNem Mini PMI-P (-20°C, 80°C) ,From 1 to 18°F for ProNem Mini

PMI-P (-4°F,176°F),From 0.1 to 10.0°C for ProNem Mini PMI-P (-20.0°C,80.0°C)

From 0.1 to 18.0°F for ProNem Mini PMI-P (-4.0°F,176.0°F).

Minimum Temperature Set Value Parameter ( Default = 10.0°C)

Temperature set value can not be lower than this value. This parameter value can be

adjusted from minimum value of device scale to maximum temperature set value

parameter

Maximum Temperature Set Value Parameter ( Default = 40.0 °C )

Temperature set value can not be greater than this value.

This parameter value can be adjusted from minimum temperature set value parameter

to maximum value of the device scale.

From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)

From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)

From -10.0 to 10.0°C , NTC ,PTC , PT-100 (0.0°C,100.0°C)

From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)

From -10 to 10°C ,ProNem Mini PMI-P ( -20°C, 80°C ),From -18 to 18°F,ProNem Mini PMI-

P ( -4°F, 176°F ),From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C ),

From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )

0..10V 0..20mA Z or Z

2..10V 4..20mA Z or Z

(1) (2)

(2)(1)

It is valid, if the device type 0/2...10V

It is valid, if the device type 0/4...20mA

Z Humidity Sensor Input.

Z Humidity Sensor Input .

(1)

(2)

Humidity input range is determined with this parameter.

Note : parameter ProNem Mini PMI-P type device are not observed.

Hysteresis Parameter for Humidity ( Default = 1 )

From 1 to 10 for Humidity Sensor (0%RH, 100%RH)

From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)

In ON/OFF control algorithm,

value is tried to keep equal to set value by

opening or closing the last control element.

ON/OFF controlled system, temperature

value oscillates continuously. Temperature

value’s oscillation period or amplitude

around set value changes according to

controlled system. For reducing oscillation

period of temperature value, a threshold

zone is formed below or around set value

and this zone is named hysteresis.

Humidity

OFF

Humidity

Control

Output

Set

hhSt

Time

hhSt

Time

Maximum Humidity Set Value Parameter (Default = Maximum Value of Device Scale)

This parameter value can be

adjusted from minimum humidity set value parameter to maximum value of the

device scale.

Humidity set value can not be greater than this value.

Minimum Humidity Set Value Parameter (Default = Minimum Value of Device Scale)

set value can not be lower than this value. This parameter value can be adjusted

from minimum value of device scale to maximum set value parameter

Humidity

Humidity Sensor Offset Parameter ( Default = 0.0 )

From -10 to 10%RH for (0%RH-100%RH)

From -10.0 to 10.0%RH for (0.0%RH-100.0%RH)

Humidity Sensor

Temperature Alarm is inactive.

Temperature Alarm Set Parameter

This parameter value can be programmed between temperature minimum alarm set

parameter and temperature alarm set maximum parameter.

( Default = 50.0 °C )

Temperature Alarm Function Selection Parameter ( Default = 0 )

Process High alarm selected.

Process Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Alarm Set Maximum Parameter ( Default = Maximum Value of Device Scale)

if temperature alarm is active, this parameter value can be adjusted from temperature

alarm set value parameter to maximum value of the device scale.

Alarm Set Minimum Parameter (Default = Minimum Value of Device Scale)

if temperature alarm is active, this parameter value can be adjusted from minimum value of

device scale to temperature alarm set maximum parameter value.

Temperature Alarm Parameter

This parameter value can be adjusted form 0 to %50 of the device scale.

Hysteresis ( Default = 0)

Temperature Alarm On Delay Time Parameter

Temperature Alarm On Delay Time can be defined with this parameter. It can be

adjusted from 0 to 99 minutes.

( Default = 0)

Temperature Alarm Delay After Power On Parameter

It can be adjusted from 0 to 99 minutes.

( Default = 0)

When power is first applied to the device, this time delay must be expired for activation of

temperature alarm.

Process High alarm selected.

Process Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Humidity Alarm Set Parameter

This parameter value can be programmed between humidity minimum alarm set

parameter and humidity alarm set maximum parameter.

( Default = 60 )

Humidity Set Minimum Parameter(Default =Minimum Value of Device Scale)

if humidity alarm is active, this parameter value can be adjusted from minimum value of

device scale to humidty alarm set maximum parameter value.

Alarm

Humidity Alarm Parameter

This parameter value can be adjusted form 0 to %50 of the device scale.

Hysteresis ( Default = 0)

Buzzer Active Time

If buzzer function selection parameter

Buzzer active time can be define with this parameter. It can be adjusted from 1 to 99

minutes. When this parameter is 1, if decrement button is pressed, is observed. In

this condition buzzer is active till buzzer silence button is pressed.

( Default = )

value = 0, this parameter is not observed.

Note-1: External Fuse is recommended

WHITE

YELLOW

BROWN

GREEN

ProNem Mini

PMI-P

BLACK

Shield

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

ESM-3723

SET

HEAT.

ALARM

HUM.

ALARM/

HEAT

230 VV ± 15%

50/60Hz - 1.5VA

230 VV ± 15%

50/60Hz - 1.5VA

HEAT

ALARM

HUM.

HEAT

HUM.

ALARM/

Humidity Alarm is inactive.

Note : If this parameter is select 0, Temperature Alarm parameters , , , , and

will be not observed.

Note : If this parameter is select 0, Humidity Alarm parameters , , , , and

will be not observed.

Note : When value of or parameters are changed , the values of , , , ,

, , , , , , , , , , , , and parameters

should be changed accordingly.

Note : Shield (Black) pin must be connected to number 10 (GND) of the terminal block.

P/N : ESM-3723 - 5.6.6.0.1/01.01/1.6.6.0

P/N : ESM-3723-5.2.5.0.1/01.01/1.2.0.0

It is valid, if the device type 0/2...10V

It is valid, if the device type 0/4...20mA

Z Sensor Input.

Z Sensor Input

Temperature

Temperature .

(1)

(2)

0..10V veya 0..20mA Z Z

2..10V veya 4..20mA Z Z

Temperature Sensor Scale Selection Parameter ( Default = 0 )

(1) (2)

(2)(1)

Analogue (T input range is determined with this parameter.emperature)

Temperature

Sensor Scale Low Limit Parameter : ( Default = 0 )

It can be adjusted from -1999 to ( -1). At this value analogue input becomes;

If =0, according to the device type 0V 0mA

If =1, according to the device type 2V 4mA

(1) (2)

Temperature

Sensor Scale High Limit Parameter : ( Default = 100 )

It can be adjusted from ( +1) to 9999. At this value analogue input becomes;

According to the device type 10V 20mA ZZ

(1) (2)

Note : , parameters are shown, if the Temperature sensor analogue input type is selected .

Note : , and parameters are shown, if the Temperature sensor analogue input type

( 0/2..10V or 0/4..20mA ) is selected.