User manual

2.2PanelCut-Out
2.GeneralDescription
2.1FrontViewandDimensionsofESM-3711HNTemperatureController
MountingClamp
PanelSurface
(maximumthickness15mm/0.59inch)
FrontPanel
IP65protection
ESM-3711HN77x35 DINSize HeatingController
InstructionManual.ENGESM-3711HN01V0011/14
-4DigitsDisplay
-NTCInputor
PTCInputor
(Mustbedeterminedinorder.)
- Adjustabletemperatureoffset
-Temperaturecontrolwithmanualheatingfunction
- Alarmparameters
- Adjustableinternalbuzzeraccordingtocookingtime,sensor
defectand Alarmstatus.
-Passwordprotectionforprogrammingsection
-InstallingparametersusingProkey
-Remoteaccess,datacollectingandcontrollingwithModbusRTU
-HavingCEmarkaccordingtoEuropeanNorms
-
JTypethermocoupleInputor,
KTypethermocoupleInputor,
2-WirePT-100Inputor,
2-WirePT-1000Input
ON/OFFtemperaturecontrol
- Adjustabletemperatureoffset
-RelayorSSRdriveroutput
-DigitalInput(CookingTimeStart/StopInput)
- Adjustablecookingtimefromfrontpanel
-Temperaturecontrolaccordingtothecookingtime(Timer)
-Usercanselecttostartcookingtime(Timer)whentemperature
reachestothesetvalue
-Buttonprotection
-Setvaluelowlimitandsetvaluehighlimitboundaries
ESM- 77x35DINSize3711HN
Digital,ON/OFFTemperature
Controller
OperatingTemperature:
Max.OperatingHumidity :
Altitude :
0to50°C
90%Rh(non-condensing)
Upto2000m.
Forbidden Conditions:
Corrosive atmosphere
Explosive atmosphere
Home applications (The unit is only for industrial applications)
c
1.2GeneralSpecifications
1.Preface
ESM-3711HN series heating controllers are designed for measuring and controlling
temperature. They can be used in many applications with their easy use, On/ Off control form
and cooking time properties. Some application fields which they are used are below:
ApplicationFields Applications
Glass Heating
Food BakingOvens
Plastic Incubators
Petro-Chemistry Storages
Textile, Automative AirConditioning
MachineProductionIndustriesEtc... Etc...
2
1.1EnvironmentalRatings
3 41615
13 14
A visual inspection of this product for possible damage occurred during shipment is
recommended before installation. It is your responsibility to ensure that qualified mechanical
and electrical technicians install this product.
If there is danger of serious accident resulting from a failure or defect in this unit, power off the
system and separate the electrical connection of the device from the system.
The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse
as required.
Be sure to use the rated power supply voltage to protect the unit against damage and to prevent
failure.
Keep the power off until all of the wiring is completed so that electric shock and trouble with the
unit can be prevented.
Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in
malfunction, electric shock or fire.
Do not use the unit in combustible or explosive gaseous atmospheres.
During putting equipment in hole on the metal panel while mechanical installation some metal
burrs can cause injury on hands, you must be careful.
Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage
of the device with inappropriate fixing clamp. Be sure that device will not fall while doing the
montage.
It is your responsibility if this equipment is used in a manner not specified in this instruction
manual.
EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts
from the delivery date. This warranty is in force if duty and responsibilities which are determined
in warranty document and instruction manual performs by the customer completely.
Repairs should only be performed by trained and specialized personnel. Cut power to the
device before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of
these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in
ethyl alcohol or water to clean the external plastic case.
1.3Installation
1.4Warranty
1.5Maintenance
1.6ManufacturerCompany
ManufacturerInformation:
Repairandmaintenanceserviceinformation:
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY
Phone:+902242611900
Fax:+902242611912
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA /TURKEY
Phone:+902242611900
Fax:+902242611912
DeviceType
Housing&Mounting
ProtectionClass
Weight
EnvironmentalRatings
Storage/OperatingTemperature
Storage/OperatingHumidity
Installation
OvervoltageCategory
PollutionDegree
OperatingConditions
SupplyVoltageandPower
TemperatureSensorInput
NTCinputtype
PTCinputtype
Thermocoupleinputtype
Thermoresistanceinputtype
Accuracy
ColdJunctionCompensation
SensorBreakProtection
SamplingCycle
ControlForm
RelayOutputs
OptionalSSRDriveOutput
Display
LED
InternalBuzzer
:HeatingController
:76mmx34.5mmx71mmplastichousingforpanel
Mounting.Panelcut-outis71x29mm.
:Ip65atfront,Ip20atrear.
: Approximately0.20Kg.
:Standard,indooratanaltitudeoflessthan2000meters
withnonecondensinghumidity.
:-40 Cto+80 C/-30 Cto+80 C
:90%max.(Nonecondensing)
:Fixedinstallation
:II.
:II,officeorworkplace,noneconductivepollution
:Continuous
:
:115
:24
:24
:10-30
:NTC,PTC, TC,RTD
:NTC(10k @25°C)
:PTC(1000 @25°C)
:J,K(IEC584.1)(ITS90)
:PT-100,PT-1000(IEC751)(ITS90)
:±1%offullscaleforthermoresistance
: Automatically±0.1°C/±1°C
:Upscale
:3samplespersecond
:ON/OFF
: A@250V forResistiveload(Compressoroutput)
(Electricallife:100.000switchingatfullload)
:Maximum20mA,Maximum17V
:14mmRed4digitsLEDDisplay
:S(Green),P (Green), C(Yellow), F(Yellow),
CompressorOutput(Red),HeatingOutput(Red)
: 83dB
:,
o o o o
o o
W
W
³
16(8) V
Approvals
230V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V 1.5WZ
Z
V
V
V
W
±
±
±
±
8.Specifications
All order information of ESM-3711HN Heating Controller are given on the table at above. User may
form appropriate device configuration from information and codes that at the table and convert it to the
ordering codes. Firstly, supply voltage then other specifications must be determined. Please fill the order
code blanks according to your needs. Please contact us, if your needs are out of the standards.
V
Z
Vac,
Vdc
Vdc or Vac
can be applied
Þ
Þ
ÞW
c
11.OrderingInformation
Note-1:If input type is selected PTC or NTC (BC= 12, 18), Temperature sensor is given with the
device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is
selected as NTC, sensor type (V = 0,3 or 4) must be declared in ordering information.
ESM-3711HN
PowerSupply
Input
TemperatureSensor
Input
76mm/3inch
6mm/0.24inch
34,5mm/1.36inch
65mm/2.56inch
Maximum15mm/0.59inch
110mm/4.33inch(min)
71mm/2.79inch
29mm/1.14inch
50mm/1.97inch(min)
230V ( %15)50/60HzV ±
OptionalSupplyVoltage
-30V Z
115V ( %15)50/60Hz,
24V ( %15)50/60Hz,
24V ( %15)50/60Hz,
10
±
±
±
V
V
W
Standard
A BC D E FG HI /
/
U
V W Z/
/
0 1 0 0
1
RelayOutput(16(8) A@250V ,atresistiveLoad,1NO)V
Output-1
E
SupplyVoltageA
InputType
BC
Scale(°C)
ESM-3711HN
4
-50°C/-58°F; 150°C/302°F
12
PTC(Not-1)
Temp.Sensorwhichisgivenwith ESM-3711HN
V
0
None
3
NTC-M5L20.K1.5(NTCSensor,thermoplasticmouldedwith1.5mcable
forcoolingapplication)
4
NTC-M6L50.K1.5(NTCSensor,stainlesssteelhousingwith1.5mcable
forcoolingapplication)
9
Customer
115V ( %15)50/60Hz-1.5VAV ±
5
230V ( %15)50/60Hz-1.5VAV ±
00 00
8
10-30V Z
-50°C/-58°F; 100°C/212°F
18
NTC(Not-1)
1
PTC-M6L40.K1.5(PTC AirProbe1.5mtSiliconCable)
2
PTCS-M6L30.K1.5.1/8”(PTCLiquidProbe1.5mtSiliconCable)
(77x35DINSizes)
10.Optional Accessories
RS-485CommunicationInterface
1.RS-485Module 2.PROKEY ProgrammingModule
Thedeviceisprogrammed(Uploador
Download)byusingtheparameters.
0°C/32°F; 800°C/1472°F
05
J,FeCuNiIEC584.1(ITS90)
0°C/32°F; 999°C/1830°F
10
K,NiCrNiIEC584.1(ITS90)
-50°C/-58°F; 400°C/752°F
11
PT 100,IEC751(ITS90)
-19.9°C/-4°F; 99.9°C/212°F
09
PT 100,IEC751(ITS90
-50°C/-58°F; 400°C/752°F
14
PT 1000,IEC751(ITS90)
-19.9°C/-4°F; 99.9°C/212°F
13
PT 1000,IEC751(ITS90
3
24V ( %15)50/60Hz-1.5VAV ±
NTC,PTC,
JorKTypeTC
2-WirePT-100
PT-10002-Wire
Output-1
ControlOutput
AlarmOutput
Output-1
Standard
Optional
(RelayOutput)
(SSRDriveOutput)
HeatingFunction
ON/OFFOperation
ControlOutput
AlarmOutput
2
SSRDriver Maximum20m,Maximum17VOutput( )Z
2
24V ( %15)50/60Hz-1.5VAW ±
DigitalInput
CookingTime(Timer)
Start/StopInput
WhenSET buttonispressedfor5
seconds,“P”ledstartstoblink.If
programmingmodeentering
passwordisdifferentfrom0,
programmingmodeenteringscreen
willbeobserved.
MainOperationScreen
ProgrammingScreen
Changethevaluewithincrement
anddecrementbuttons.
TemperatureUnitSelection
ParameterValue
Press SET button for accessing to the parameter
value. Press increment button for accessing to the
next parameter, press decrement button for
accessing to the previous parameter.
PressOKbuttonforsavingthe
parameter.
Press increment button for accessing to the
next parameter, press decrement button for
accessing to the previous parameter
PasswordEnteringScreen
ProgrammingMode
EnteringScreen
PressOKbuttonfor
accessingtothe
passwordentering
screen.
PasswordEnteringScreen
Enterprogrammingmodeaccessingpassword
withincrementanddecrementbuttons.
Note2: If programming mode accessing password is 0, only three parameters are accessible, and the
parameter values can be changed.
PressOKbuttonforentering
thepassword.
Note1: Ifprogramming
modeaccessing
passwordis0,
TemperatureUnitscreen
isobservedinsteadof
programmingscreen
TemperatureUnitSelection
ParameterValue
If no operation is performed in programming mode for 20 seconds, device turns to main
operation screen automatically..
i
DecimalSeperator
EnablingParameter
6.6EnteringToTheProgrammingMode,ChangingandSavingParameter
6.5OperationGraphicsofESM3711HNHeatingController
3- When cooking time parameter 1, if selection of temperature control and starting the
cooking time parameter = 2 ( Temperature control and cooking time (Timer) can be started
by pressing cooking ON/OFF button or when
is selected;
³
cooking time start/stop input is getting closed
condition)
Hst
°C
Buzzeris
Active
Cooking
Buttonstarts
time
Hst
°C
(ContinuousOperation)
=
(Interrupted )Operation
=
0
1
=1
4-ManualControl:Ifcookingtime(Timer)
=
Hst
°C
TemperatureControl
is Active
Power
Time
Hst
Process
Set
Process
Output
°C
Temperature
Control
is Active
=
Cooking
Buttonstarts
thetemperature
control
=
0or1
=
2
Cooking
Time
Active
Led
(TemperaturecontrolstartswithcookingON/OFFbuttonor
when )cookingtimestart/stopinputisgettingclosedcondition
(Temperaturecontrolstartsatpoweron)
Time
Time
Time
Time
Time
Time
Time
Process
Output
Process
Set
Cooking
Time
Active
Led
Power
Cooking
Buttonstarts
thetemperature
control
Cooking
Buttonstops
thetemperature
control
Cooking
Buttonstops
thetemperature
control
Temperature
Control
is Active
Power
Power
Cooking
Time
Active
Led
Cooking
Time
Active
Led
Process
Set
Process
Set
Temperature
Control
is Active
Temperature
Control
is Active
Process
Output
Process
Output
Time
Time
Time
Time
TemperatureControl
is Active
Cooking
Buttonstarts
time
Cooking
Buttonstarts
time
Cooking
Buttonstarts
time
Time
Time
Time
Time
Buzzeris
Active
=1
YourTechnologyPartner
www.emkoelektronik.com.tr
Thankyouverymuchforyourpreferenceto
useEmkoElektronikproducts,pleasevisitour
webpagetodownloaddetailedusermanual.
7.CookingTime(Timer)ON/OFFOperation
ü
3sec.
In main operation screen, If cooking button is pressed for
3 seconds, then cooking time (Timer) is started and
cooking time active led becomes active. While cooking
time (Timer) continues if cooking button is pressed for 3
seconds, cooking time (Timer) is finished and cooking
time active led lights off.
If button protection parameter = 4 cooking time
(Timer) ON/OFF operation is performed when
button is pressed.
7.1CookingTime(Timer)ON/OFFOperationwithCookingTimeStart/StopInput
When K switch that is connected to the cooking time
start/stop input, getting closed condition, cooking time
(Timer) is started and cooking time active led becomes
active. While cooking time (Timer) continues if K switch
getting open condition, cooking time (Timer) is finished
and cooking time active led lights off.
DIGITAL INPUT
K
6
7
ü
O
F
O
C
S
P
ü
O
F
O
C
S P
ü
O
F
O
C
S P
ü
O
F
O
C
S P
ü
ü
O
F
O
C
S P
ü
O
F
O
C
S P
1- Screen Blinking
Sensor failure . Sensor connection is wrong or there is no sensor connection. If buzzer function
selection parameter is 3 or 4, internal buzzer starts to operate.
9.FailureMessagesinESM-3711HNHeatingController
Example:Ifalarmfunctionselectionparameterinprogrammingsectionis1(Absolute Alarm)
andmaximumalarmparameteris50Whentemperatureisabove50°C,valueonthescreen
startstoblink. Alsobuzzerfunctionselectionparameteris2or4,theninternalbuzzerison.
2- Main Screen Value is Blinking.
ü
ü
ü
O
F
O
C
S P
O
F
O
C
S P
O
F
O
C
S P
O
F
O
C
S P