User manual

ManualsBrandsEMKO ManualsElectronic Control SystemsTemperature controller (L x W x H) 90 x 48 x 48 mm

PO1

PO2

°C

°F

LITE

Eco

AL1

PO1

PO2

°C

°F

LITE

Eco

AL1

1- Before mounting the device in your

panel, make sure that the cutout is of

the right size.

2- Check front panel gasket position.

3- Insert the device through the cutout.

If the mounting clamps are on the unit,

put out them before inserting the unit to

the panel.

4- Insert the mounting clamps to the two

of designated holes that located four

sides of device.

5- Drag the mounting clamps in

direction 5 until the device completely

immobile within the panel.

6- In order to rem ove device push on

the mounting clamp as shown with

arrow 6 and pull back.

Introduction Brochure. ENG EcoLITE 01 V00 10/16

DISPLAY

Process Display: 16 mm Red 3 digit LED Display

Set Value Display: 9 mm Orange 4 digit LED Display

Led Indicators: PO1 (Process Output-1 Status Led), PO2 (Process

Output-2 Status Led), ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operating Temperature: 0...50ºC

Humidity: 0-90%RH (none condensing)

Protection Class: IP65 at front, IP20 at rear

Weight: 150 gr.

Dimension: 48 x 48 mm, Depth: 86,5 mm

Panel CutOut: 46 x 46 mm

Access and Change Set Values

: Output-1 Parameters

: Operation Type Selection for Output-1. It can be or .

(Default: )

: Hysteresis Value for Output-1. It can be adjusted from %0 to %50 of

the Operation Scale ( - ). (Default: 3)

: Set1 Value Low Limit. Minimum Set1 value is defined with this

parameter. It can be adjusted from Operation Scale Low Limit( ) to

Set1 High Limit( ). (Default: 0)

: Set1 Value High Limit. Maximum Set1 value is defined with this

parameter. It can be adjusted from Set1 Low Limit( ) to Operation

Scale High Limit( ). (Default: 500)

: Minimum Pulling Time for Output-1. When Output-1 is inactive this

time must be expired for Output-1 to become active again. It can be

adjusted from 0 to 100 seconds. (Default: 0)

: Protecion Menu Parameters

: Password for accessing to the programming section. It can be

adjusted from 0 to 9999.If is 0, password screen is not seen. If

is different from 0 and user enters to the menu pages without entering the

password, all menus can be seen except protection menu . But

device does not allow to do any changes in parameters. (Default: 0)

: User default parameters. This parameter is used for saving all

parameters to restore later or restore all parameters saved before. If

is chosen, all parameters saved before are restored. If is chosen, all

parameters saved to restore later. If is chosen, nothing is changed.

(Default: )

: This parameter is used for restore factory defaults. If is chosen,

factory defaults parameters restored. If is chosen, nothing is changed.

(Default: )

Eco LITE, On/Off Temperature Control Unit

- 3 digit process (PV) and 4 digit set (SV) display

- Process input (TC,RTD)

- ON/OFF control form

- Selectable heating and cooling function

- Operating type selection with hysteresis

-Adjustmentoftemperatureoffsetvalue

- Minimum pulling time adjustment for control outputs

- Password protection for programming mode

Eco series temperature controllers are designed for measuring and

controlling temperature. They can be used in many applica tions with

their TC and RTD temperature measurement input, On/Off control form

and heating and cooling selection.

They are mainly used in glass, plastic, petro-chemistry, textile,

automotive and machine production industries.

SPECIFICATIONS

Process Input: TC, RTD

Thermocouple (TC): J, K, R, S and T(IEC584.1)(ITS90)

Termoresistance (RTD): PT-100 (IEC751)( ITS90)

Measurement Range: Please refer to process input type selection in

process menu parameters section.

Accuracy: ± 0.25% of scale for thermocouple and thermoresistance

Cold Junction Compensation:Automatically ±0.1°C/1°C

Line Compensation: Maximum 10 Ohm

Sensor Break Protection: Upscale

Sampling Cycle: 0.1 second

Input Filter: Programmable

Control Form: ON/OFF

ON/OFF Hysteresis: It can be configured for two control outputs

OUTPUT

Process Output - 1: Relay (5A@250V at resistive load)

Process Output - 2: Relay (5A@250V at resistive load)

ON/OFF TEMPERATURE CONTROL UNIT

LITE

Eco

SUPPLY VOLTAGE

230V (±15%) 50/60Hz - 2VA

115V (±15%) 50/60Hz - 2VA

10...30V - 2W

(It must be determined in order)

Electrical Wirings

The Device with One Relay:

The Device with Two Relays:

To reduce the effect of electrical noise on device, low voltage line (especially sensor

input cable) wiring must be separetely from high current and voltage line. If possible,

use shielded cable and shield must be connected to ground only one side.



LITE

Eco

Process

Input

5A@250V

PT-100

Supply

Switch

Supply

Voltage

1A T

Fuse

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

PT-100

Supply

Switch

Supply

Voltage

1A T

Fuse

LITE

Eco

Dimensions

6 mm / 0.24 inch

80,52 mm / 3.17 inch

Maximum 9 mm / 0.35 inch

48 mm / 1.89 inch

PO1

PO2

°C

°F

LITE

Eco

AL1

Panel Mounting

PO2

PO1

AL1

AL2

°C

°F

Press increment or decrement

button to change Set1 value.

Press Enter button to save new

Set1 value and open Set2 screen.

Main Screen

PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

Main Screen

PO2

PO1

AL1

AL2

°C

°F

/PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

Press increment or decrement

button to change Set2 value.

Press Enter button to save new

Set2 value and return main screen.

Note1: User can exit from set value section without saving the values by pressing

button. If no operation for 120 seconds, device automatically exits from Set Value

section.

Note2: Displayed set value at main screen could be changed according to

parameter

PO2

PO1

AL1

AL2

°C

°F

Main Screen

PO2

PO1

AL1

AL2

°C

°F

/PO2

PO1

AL1

AL2

°C

°F

Password Screen

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

/ PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

PO2

PO1

AL1

AL2

°C

°F

To enter program menu

press button

Enter Password with

increment or decrement buttons.

Approve password

with Enter button

*1 - Minimum pulling time parameter for Output-1( ) is not seen unless operation

type selection for output-1 param eter( ) is set as .

*2 - Out-2( ) parameters are not seen on devices with one relay.

*3 - Alarm parameters( , and ) are not seen unless operation type

selection for output-2 parameter( ) is set as .

*4 - Minimum pulling time parameter for Output-2( ) is not seen unless operation

type selection for output-2 param eter( ) is set as .

*5 - If is different from 0 and user enters to program menu without entering the

password menu is not seen.

Note: User can exit from any parameter screen without saving the values by

pressing button. If no operation for 120 seconds, device automatically return to

the main screen.

Easy Access Diagram For Program Parameters

: Process input type selection. (Default: )

: J type (Fe,Cu,Ni) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF

: K type (Ni,Cr,Ni) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF

: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF

: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF

: T type (Cu,Cu,Ni) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF

: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF

: Unit Selection. or can be chosen. (Default: )

: Operation Scale minimum (Low Limit) value. It changes according

to the process input type and scale. (Default: -199)

: Operation Scale maximum (High Limit) value. It changes according

to the process input type and scale. (Default: 900)

: Display offset for process value. It can be adjusted from -10% of

scale to 10% ofscale. It is added to the process display value. (Default: 0)

: Define filter time(sec) for displayed value. (Default: 1.0)

: Selection of which set value displayed at main screen.

(Default: )

: Process Menu Parameters

: Output-2 Parameters (Only for devices with two relays)

: Operation Type Selection for Output-2. It can be or .

(Default: )

: Hysteresis Value for Output-2. It can be adjusted from %0 to %50 of

the Operation Scale ( - ). (Default: 3)

: Alarm type selection. See "Alarm Types" section. (Default: )

: Set2 Value Low Limit. Minimum Set2 value is defined with this

parameter. It can be adjusted from Operation Scale Low Limit( ) to

Set1 High Limit( ). (Default: 0)

: Set2 Value High Limit. Maximum Set2 value is defined with this

parameter. It can be adjusted from Set2 Low Limit( ) to Operation

Scale High Limit( ). (Default: 500)

: Minimum Pulling Time for Output-2. When Output-2 is inactive this

time must be expired for Output-2 to become active again. It can be

adjusted from 0 to 100 seconds. (Default: 0)

: Alarm on Delay Time. It can be adjusted from 0 to 9999 seconds.

(Default: 0)

: Alarm off Delay Time. It can be adjusted from 0 to 9998 seconds. If

it is higher than 9998, is seen on the screen and alarm latching

output is selected. In alarm latching output mode in order to make

passive alarm outputs, press enter button at main screen. (Default: 0)

Remove all input/output connections on terminals before

restoring parameters to user/factory defaults.



Summary of content (2 pages)

PAGE 1
*ccess and Change Set Values Electrical Wirings ONgOFF TEMPER*TURE CONTROL UNIT The Device with One Relayv f L NO C j Wm WW W, ) b T Supply %A "use Switch TC U ( PTMWmm N Wf *LW g PO, Eco LITE Process Input NO :A±H:0V :A±H:0V NO C U L T Supply %A "use Switch � j Wm W, ) Wf Eco LITE TC ( b *L, g PO, PAlarm Output H or Process Output H( *LW PAlarm Output %( WW PTMWmm N Supply Voltage w POW POW *LW *LW *LW *L, g PO, *L, g PO, *L, g PO, Press increment or decremen
PAGE 2
Other Informations Error Messages 8SSensor failure in analog inputsE Sensor connection is wrong or there is no sensor connectionE °C °F a PO8 AL8 ALx T POx °C °F PO8 AL8 ALx T POx xSIf programming section entering password is different from “z” and user accesses to the parameter by enter button without entering the password and wants to change a parameterM the warning message is shown on the bottom display as shown on the leftE ±evice does not allow to do any changes without entering the password cor